參數資料
| 型號： | 8284 |
| 廠商： | 3M |
| 文件頁數： | 1/2頁 |
| 文件大小： | 0K |
| 描述： | FLOOR RUNNER ESD BLUE 2' X 40' |
| 產品變化通告： | 8200 Series Material Change 22/Feb/2012 |
| 視頻文件： | Anti-Fatigue Mat |
| MSDS 材料安全數據表： | 8200 Series MSDS |
| 標準包裝： | 1 |
| 墊子類型： | 地板卷筒 |
| 形狀： | 矩形 |
| 長度： | 40'（12.19m） |
| 寬： | 2'（0.61m） |
| 厚度： | 0.14"（3.56mm） |
| 顏色： | 藍 |
| 材質： | 乙烯基 |
| 特點： | 耗散 |
| 包括： | 接地軟線（2），接地卡扣（2） |
| 相關產品： | SCP274-ND - SNAP FASTENER 10MM FEMALE 1=10PC SCP275-ND - SNAP FASTENER FEMALE 10MM 1=10PC SCP114-ND - GND CORD 15FT FOR MATS |
| 其它名稱： | 82843M 82843M-ND 98079828848 SCP280 |
The basic purpose of conductive work surfaces is to
provide a surface that is free of static charge and also is
capable of removing the static charge from conductive
items placed on it. The total resistance to ground
determines the level of charge and rate at which it will be
drained. A resistance to ground of 1000 megohms or less is
required on an 8200 mat to drain a charge to a level of 100
volts or less in one second from a person or tote box
charged to 5KV (ref.1, 2).
Resistance Measurement:
Measuring the resistance of the mat requires a high voltage
megohmmeter. The megohmmeter must have a test voltage
of 50-100 volts and a meter range of 0-1000 megohms. The
ground lead of the megohmmeter is attached to the ground
points of the mat. The other lead of megohmmeter is
attached to an electrode that is described in both ASTM F
150 and NFPA 56A paragraph 4-6.2.7(b).
The resistance to ground should be greater than 106
ohms and less than 109 ohms. if the resistance is less than
106 ohms, an alternate path to ground has been established
which bypasses the one megohm resistor in the ground
cord. If the resistance is greater than 109 ohms, the ground
connection has been interrupted.
Cleaning:
Mats should be periodically cleaned with a detergent and
water solution. To reduce the possibility of leaving a
residue, detergents (rather than soaps) should be used.
Powdered detergents such as Tide, Ajax, etc. should be
added to water at a 1-2% concentration, liquid detergents
such as Wisk, All, etc. at a 2-3% concentration, and
general purpose cleaners such as 409, Mr. Clean, etc. can
be used full strength.
Normally, only a cloth that is thoroughly wetted with the
detergent solution is needed to wipe off the mat; however,
hardened stains may require brushing with a semirigid
bristled brush. The wiping or brushing action should be in a
circular motion to ensure removal of the particles from the
surface depressions. Extremely soiled mats may require
several repeated cleanings with a water rinse between each
cleaning. The water rinse should consist of wetting a cloth
with clean water and wiping the surface to remove loosened
dirt and detergent.
The final step should be to use a cloth dampened with
isopropanol and wipe the mat to remove any organic
contamination as well as the residual detergent. Avoid
using excessive isopropanol because the bottom foam layer
will absorb the solvent and cause the mat to swell.
Regardless of the technique used to clean the mats, the
previously described resistance measurement should be
performed to verify that the mat is functional.
Note: Read all Health Hazard, Precautionary, and First Aid
statements found in the Material Safety Data Sheet (MSDS)
and/or product label of cleaning materials prior to handling
or use.
Reference:
1.
D. M. Yenni, Jr. "Basic Electrical Considerations in
the Design of a Static-Safe Work Environment", Proc.,
(NEPCON/WEST), March 1979, pp. 273-284.
2.
J. R. Huntsman, D. M. Yenni, Jr., "Test Methods for
Static Control Products", Proc., EOS/ESD Symposium
1982, pp. 94-109.
Maintenance of Static Control
Systems 8200 Mats
Technical Brief – July, 1983
No. 113
3
Megohmmeter
Table
Mat
NFPA 56A
Electrode
Ground
Connection
相關PDF資料 |
PDF描述 |
|---|---|
| 430615-20-0 | TERM BARRIER 20CIRC 1 ROW .4375 |
| 4306R-104-180/390 | RES NET MULT OHM 8 RES 6-SIP |
| PC-11403 | BOX POLY 1.53"X 7.06"X 5.30"GRY |
| 430610-20-0 | TERM BARRIER 20CIRC 1 ROW .4375 |
| 430603-20-0 | TERM BARRIER 20CIRC 1 ROW .4375 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 82-84 | 制造商:n/a 功能描述:CONNECTORS NXH1B |
| 82840 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| 82840001 | 功能描述:12VDC 5000 RPM RoHS:是 類別:電機，螺線管 >> 電機 - AC，DC 系列:- 標準包裝:1 系列:OMNUC G 類型:伺服 AC 電壓 - 額定:200VAC RPM:1000 RPM 直徑 - 主體:6.93"（176.00mm） 直徑 - 軸:1.38"（35.00mm） 長度 - 軸和支架:3.15"（80.00mm） 安裝孔間距:7.87"（200.00mm） 特點:絕對式編碼器，鍵 端接類型:連接器 轉矩 - 運行（oz-in / mNm):4021.8 / 28400 轉矩 - 啟動狀態 (oz-in / mNm):- 轉矩 - 停滯狀態 (oz-in / mNm):- 齒輪減速比:無 電壓范圍:- 功率（瓦特）:3kW 重量:55 磅（24.9kg） 其它名稱:R88MG3K010TS2 |
| 82840002 | 功能描述:24VDC 5000 RPM RoHS:是 類別:電機，螺線管 >> 電機 - AC，DC 系列:- 標準包裝:1 系列:OMNUC G 類型:伺服 AC 電壓 - 額定:200VAC RPM:1000 RPM 直徑 - 主體:6.93"（176.00mm） 直徑 - 軸:1.38"（35.00mm） 長度 - 軸和支架:3.15"（80.00mm） 安裝孔間距:7.87"（200.00mm） 特點:絕對式編碼器，鍵 端接類型:連接器 轉矩 - 運行（oz-in / mNm):4021.8 / 28400 轉矩 - 啟動狀態 (oz-in / mNm):- 轉矩 - 停滯狀態 (oz-in / mNm):- 齒輪減速比:無 電壓范圍:- 功率（瓦特）:3kW 重量:55 磅（24.9kg） 其它名稱:R88MG3K010TS2 |
| 82840003 | 功能描述:12VDC 5000 RPM AP RoHS:是 類別:電機，螺線管 >> 電機 - AC，DC 系列:- 標準包裝:1 系列:OMNUC G 類型:伺服 AC 電壓 - 額定:200VAC RPM:1000 RPM 直徑 - 主體:6.93"（176.00mm） 直徑 - 軸:1.38"（35.00mm） 長度 - 軸和支架:3.15"（80.00mm） 安裝孔間距:7.87"（200.00mm） 特點:絕對式編碼器，鍵 端接類型:連接器 轉矩 - 運行（oz-in / mNm):4021.8 / 28400 轉矩 - 啟動狀態 (oz-in / mNm):- 轉矩 - 停滯狀態 (oz-in / mNm):- 齒輪減速比:無 電壓范圍:- 功率（瓦特）:3kW 重量:55 磅（24.9kg） 其它名稱:R88MG3K010TS2 |
發布緊急采購，3分鐘左右您將得到回復。