參數資料
| 型號： | 8291 |
| 廠商： | 3M |
| 文件頁數： | 1/2頁 |
| 文件大小： | 0K |
| 描述： | FLOOR RUNNER ESD BROWN 4' X 40' |
| 產品變化通告： | 8200 Series Material Change 22/Feb/2012 |
| 視頻文件： | Anti-Fatigue Mat |
| MSDS 材料安全數據表： | 8200 Series MSDS |
| 標準包裝： | 1 |
| 墊子類型： | 地板卷筒 |
| 形狀： | 矩形 |
| 長度： | 40'（12.19m） |
| 寬： | 4'（1.22m） |
| 厚度： | 0.14"（3.56mm） |
| 顏色： | 棕 |
| 材質： | 乙烯基 |
| 特點： | 耗散 |
| 相關產品： | SCP274-ND - SNAP FASTENER 10MM FEMALE 1=10PC SCP275-ND - SNAP FASTENER FEMALE 10MM 1=10PC SCP114-ND - GND CORD 15FT FOR MATS |
| 其它名稱： | 82913M 82913M-ND 98079807941 SCP281 |
The basic purpose of conductive work surfaces is to
provide a surface that is free of static charge and also is
capable of removing the static charge from conductive
items placed on it. The total resistance to ground
determines the level of charge and rate at which it will be
drained. A resistance to ground of 1000 megohms or less is
required on an 8200 mat to drain a charge to a level of 100
volts or less in one second from a person or tote box
charged to 5KV (ref.1, 2).
Resistance Measurement:
Measuring the resistance of the mat requires a high voltage
megohmmeter. The megohmmeter must have a test voltage
of 50-100 volts and a meter range of 0-1000 megohms. The
ground lead of the megohmmeter is attached to the ground
points of the mat. The other lead of megohmmeter is
attached to an electrode that is described in both ASTM F
150 and NFPA 56A paragraph 4-6.2.7(b).
The resistance to ground should be greater than 106
ohms and less than 109 ohms. if the resistance is less than
106 ohms, an alternate path to ground has been established
which bypasses the one megohm resistor in the ground
cord. If the resistance is greater than 109 ohms, the ground
connection has been interrupted.
Cleaning:
Mats should be periodically cleaned with a detergent and
water solution. To reduce the possibility of leaving a
residue, detergents (rather than soaps) should be used.
Powdered detergents such as Tide, Ajax, etc. should be
added to water at a 1-2% concentration, liquid detergents
such as Wisk, All, etc. at a 2-3% concentration, and
general purpose cleaners such as 409, Mr. Clean, etc. can
be used full strength.
Normally, only a cloth that is thoroughly wetted with the
detergent solution is needed to wipe off the mat; however,
hardened stains may require brushing with a semirigid
bristled brush. The wiping or brushing action should be in a
circular motion to ensure removal of the particles from the
surface depressions. Extremely soiled mats may require
several repeated cleanings with a water rinse between each
cleaning. The water rinse should consist of wetting a cloth
with clean water and wiping the surface to remove loosened
dirt and detergent.
The final step should be to use a cloth dampened with
isopropanol and wipe the mat to remove any organic
contamination as well as the residual detergent. Avoid
using excessive isopropanol because the bottom foam layer
will absorb the solvent and cause the mat to swell.
Regardless of the technique used to clean the mats, the
previously described resistance measurement should be
performed to verify that the mat is functional.
Note: Read all Health Hazard, Precautionary, and First Aid
statements found in the Material Safety Data Sheet (MSDS)
and/or product label of cleaning materials prior to handling
or use.
Reference:
1.
D. M. Yenni, Jr. "Basic Electrical Considerations in
the Design of a Static-Safe Work Environment", Proc.,
(NEPCON/WEST), March 1979, pp. 273-284.
2.
J. R. Huntsman, D. M. Yenni, Jr., "Test Methods for
Static Control Products", Proc., EOS/ESD Symposium
1982, pp. 94-109.
Maintenance of Static Control
Systems 8200 Mats
Technical Brief – July, 1983
No. 113
3
Megohmmeter
Table
Mat
NFPA 56A
Electrode
Ground
Connection
相關PDF資料 |
PDF描述 |
|---|---|
| 4306R-104-810/131L | RES NET MULT OHM 8 RES 6-SIP |
| 1-1375820-6 | CONN RCPT HSNG 16POS CST-100 II |
| OSTYK60316130 | CONN BARRIER STRIP 16CIRC 10MM |
| 431615-21-0 | TERM BARRIER 21CIRC 1 ROW .4375 |
| 2-178128-3 | CONN RECEPT 5.08 3POS KEY-Y |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 82-91 | 功能描述:RF 連接器 HN R/A ADAPTER JACK TO PLUG UG-212A/U RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| 8291.2-L | 制造商:Ferraz Shawmut 功能描述: |
| 8291/3-OB | 制造商:Wieland Electric Inc 功能描述: |
| 829100-000 | 功能描述:BOOT MOLDED RoHS:是 類別:線纜，導線 - 管理 >> 熱收縮套，帽蓋 系列:* 標準包裝:25 系列:* 其它名稱:770228-000 |
| 82910001 | 功能描述:2PH 9 OHM PAL 9 AXE 2 RoHS:是 類別:電機，螺線管 >> 步進電機 系列:- 標準包裝:1 系列:- 類型:- 線圈類型:- 電壓 - 額定:- 每次旋轉的步數:- 步進角:- 扭矩 - 保持 (oz-in/mNm):- 直徑 - 主體:- 直徑 - 軸:- 長度 - 軸和支架:- 安裝孔間距:- 長度 - 引線:- 重量:- |
發布緊急采購，3分鐘左右您將得到回復。