- 您現在的位置：買賣IC網 > PDF目錄36335 > 935261037518 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | 935261037518 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| 封裝： | PLASTIC, SOT-341, SSOP-28 |
| 文件頁數： | 34/35頁 |
| 文件大小： | 262K |
| 代理商： | 935261037518 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁
1999 Jan 13
8
Philips Semiconductors
Product specication
5 V mixer/oscillator-PLL synthesizers for
hyperband tuners
TDA6404; TDA6405;
TDA6405A
Table 4
Address selection I2C-bus
Table 5
Test mode
Notes
1. This is the default mode at Power-on reset.
2. The ADC input cannot be used when these test modes are active.
Table 6
Reference divider ratio select bits
MA1
MA0
VOLTAGE APPLIED ON AS INPUT
0
0 to 0.1VCC
0
1
open or 0.2VCC to 0.3VCC
1
0
0.4VCC to 0.6VCC
1
0.9VCC to 1.0VCC
T2
T1
T0
TEST MODES
0
automatic charge pump off
0
1
automatic charge pump on; note 1
0
1
X
charge pump is ‘OFF’
1
0
charge pump is sinking current
1
charge pump is sourcing current
100
fREF is available on pin ADC; note 2
101
1
2fDIV is available on pin ADC; note 2
RSA
RSB
REFERENCE DIVIDER RATIO
FREQUENCY STEP (kHz)
X
0
640
6.25
0
1
1024
3.90625
1
512
7.8125
Read mode
Data can be read from the devices by setting the R/W bit
to logic 1 (see Tables 7 and 8). After the slave address
has been recognized, the devices generate an
acknowledge pulse and the first data byte (status byte) is
transferred on the SDA line (MSB first). Data is valid on the
SDA line during a HIGH-level of the SCL clock signal.
A second data byte can be read from the devices if the
processor generates an acknowledge on the SDA line
(master acknowledge). End of transmission will occur if no
master acknowledge occurs. The devices will then release
the data line to allow the processor to generate a STOP
condition. The POR flag is set to logic 1 at power-on.
The flag is reset when an end-of-data is detected by the
devices (end of a read sequence). Control of the loop is
made possible with the in-lock flag FL which indicates
when the loop is locked (FL = 1).
The ACPS flag is LOW when the automatic charge pump
switch mode is ‘ON’ and the loop is locked. In other
conditions, ACPS = 1. When ACPS = 0, the charge pump
current is forced to the LOW value.
A built-in ADC is available on ADC pin. This converter can
be used to apply AFC information to the controller from the
IF section of the television. The relationship between the
bits A2, A1 and A0 is given in Table 9.
相關PDF資料 |
PDF描述 |
|---|---|
| 935261698512 | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| 935261698518 | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| 935250380112 | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| 935250380118 | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| 935250380512 | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935261069122 | 制造商:NXP Semiconductors 功能描述:IC SECURITY TRANSPONDER PLLMC |
| 935262025112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935262217118 | 制造商:NXP Semiconductors 功能描述:Real Time Clock Serial 8-Pin SO T/R |
| 935264217557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935267356112 | 制造商:NXP Semiconductors 功能描述:IC TEA1507PN |
發布緊急采購，3分鐘左右您將得到回復。