- 您現在的位置：買賣IC網 > PDF目錄164932 > A10842RNCGE (ITT CANNON) ROTARY SWITCH-8POSITIONS, SP8T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT PDF資料下載
參數資料
| 型號： | A10842RNCGE |
| 廠商： | ITT CANNON |
| 元件分類： | 開關 |
| 英文描述： | ROTARY SWITCH-8POSITIONS, SP8T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 5/5頁 |
| 文件大?。?/td> | 338K |
| 代理商： | A10842RNCGE |
L–7
L
Rotary
C&K A Series
1-4 Pole Rotary Switches
FUNCTION
AVAILABLE HARDWARE
SPLASHPROOF
BUSHING SEAL
(FIG. 1)
(FIG. 2)
(FIG. 3)
REMOVABLE CLIP
LOCATING
TAB
STANDOFF
K EPOXY & SPLASHPROOF BUSHING SEAL
F SPLASHPROOF BUSHING SEAL
NONE NO SEAL
E
EPOXY SEAL
Stop ring
PART NO.
767B00201
Material: Brass
Finish: Nickel plated
Setting Stops on A112 and A125 Models
The number of switch positions is adjustable on A112
and A125 models only by means of a stop ring provided
with each switch. The number of positions is pre-set on
all other models and the stop ring is factory installed.
Soldering
1. Insert switch base only into PC board.
2. Do not bend terminals.
3. Wave soldering recommended at
500F solder temperature.
4. Hand solder at 500F, 10 sec.
max./terminal.
Switch Assembly
1. Hold housing/shaft assembly by housing. Remove
protective cap by squeezing tabs and discard. (FIG. 1)
2. Do not push on switch shaft. Detent mechanism will
come apart.
3. While holding switch housing, align locating tab on
base with notch on housing and engage 4 housing
latches in slots on base. (FIG. 2)
4. Push firmly on housing until latches snap in place.
5. Remove clip from shaft and discard. Assembly is
complete. (FIG. 3)
Cleaning
1. Flux clean using vapor degreaser and forced
rinse or triple bath method.
2. Do not allow switch base to ‘trap’ fluids.
3. Freon TMC, TF or Methylene Chloride give
excellent results.
To set stops: Turn shaft fully counter-clockwise and
insert stop ring tab in desired hole. Install lockwasher
and nut to retain stop ring for both PC and panel
mounting. Switch without stop ring has 12 positions.
Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
www.ittcannon.com
相關PDF資料 |
PDF描述 |
|---|---|
| A10905RSZQF | ROTARY SWITCH-9POSITIONS, SP9T, LATCHED, 0.35A, 125VDC, PANEL MOUNT-THREADED |
| A11215RSZBE | ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.02A, 20VDC, PANEL MOUNT-THREADED |
| A11242MNCBE | ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
| A10703RSMCBK | ROTARY SWITCH-7POSITIONS, SP7T, LATCHED, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
| A10703RSMCQE | ROTARY SWITCH-7POSITIONS, SP7T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A10842RNZQ | 制造商:ITT 制造商全稱:ITT Industries 功能描述:1-4 Pole Rotary Switches |
| A10842RSZQ | 制造商:ITT 制造商全稱:ITT Industries 功能描述:1-4 Pole Rotary Switches |
| A1084-A | 功能描述:GPS模塊 SiRF Star III GPS rec flash mod 3.3 RoHS:否 制造商:Linx Technologies 頻帶:1.575 GHz 通道數量:20 首次定位時間（冷啟動）:35 s 獲取敏感性:- 144 dBm 水平位置精確度:10 m 工作電源電壓:3 V to 4.2 V 工作電源電流:46 mA 接口類型:Serial 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 尺寸:15 mm x 13 mm x 2.2 mm |
| A1084-A/B | 制造商:VINCOTECH 制造商全稱:VINCOTECH 功能描述:Miniaturized GPS receiver for passive and active antennas |
| A1084-B | 功能描述:GPS模塊 SiRF Star III GPS rec flash mod 3.3 RoHS:否 制造商:Linx Technologies 頻帶:1.575 GHz 通道數量:20 首次定位時間（冷啟動）:35 s 獲取敏感性:- 144 dBm 水平位置精確度:10 m 工作電源電壓:3 V to 4.2 V 工作電源電流:46 mA 接口類型:Serial 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 尺寸:15 mm x 13 mm x 2.2 mm |
發布緊急采購，3分鐘左右您將得到回復。