- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1180LUA-T (Allegro Microsystems Inc)IC SWITCH HALL EFFECT UNI 3-SIP Datasheet資料下載
參數資料
| 型號： | A1180LUA-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 13/16頁 |
| 文件大小： | 543K |
| 描述： | IC SWITCH HALL EFFECT UNI 3-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 500 |
| 傳感范圍： | 60G ~ 200G 跳閘 - 可編程，固定釋放 |
| 類型： | 單極開關 |
| 電源電壓： | 3.5 V ~ 24 V |
| 電流 - 電源： | 5mA |
| 輸出類型： | 數字，開路集電極 |
| 特點： | 可編程 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 3-SIP |
| 供應商設備封裝： | 3-SIP |
| 包裝： | 散裝 |
Sensitive Two-Wire Field-Programmable
Chopper-Stabilized Unipolar Hall Effect Switches
A1180, A1181,
A1182, and A1183
12
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
The pulse sequences consist of the following groups of pulses:
1. An enable sequence.
2. A bit eld address sequence.
3. When permanently setting the bit eld, a long V
PH
fuse-blow-
ing pulse. (Note: Blown bit fuses cannot be reset.)
4. When permanently setting the bit eld, the level of V
CC
must
be allowed to drop to zero between each pulse sequence, in
order to clear all registers. However, when provisionally set-
ting bit elds, V
CC
must be maintained at V
PL
between pulse
sequences, in order to maintain the prior bit eld settings while
preparing to set additional bit elds.
Bit elds that are not set are evaluated as zeros. The bit eld-level
fuses for 0 value bit elds are never blown. This prevents inad-
vertently setting the bit eld to 1. Instead, blowing the device-
level fuse protects the 0 bit elds from being accidentally set in
the future.
When provisionally trying the calibration value, one pulse
sequence is used, using decimal values. The sequence for setting
the value 5
10
is shown in gure 5.
When permanently setting values, the bit elds must be set indi-
vidually, and 5
10
must be programmed as binary 101. Bit 3 is
set to 1 (000100
2
, which is 4
10
), then bit 1 is set to 1 (000001
2
,
which is 1
10
). Bit 2 is ignored, and so remains 0.Two pulse
sequences for permanently setting the calibration value 5 are
shown in gure 6. The nal V
PH
pulse is maintained for a longer
period, enough to blow the corresponding bit eld-level fuse.
V
PH
V+
t
V
PM
V
PL
0
Encode 00100
2
(4
10
)
Enable
Address
Address
Blow
Blow
Enable
Encode 00001
2
(1
10
)
Figure 6. Pulse sequence to permanently encode calibration value 5 (101 binary, or
bit eld address 3 and bit eld address 1).
V
PH
V+
t
V
PM
V
PL
0
Try 5
10
Enable
Address
Clear
Optional
Monitoring
Figure 5. Pulse sequence to provisionally try calibration value 5.
相關PDF資料 |
PDF描述 |
|---|---|
| A1184LUA-T | IC SWITCH HALL EFFECT UNI 3-SIP |
| A1186LUA-T | IC SWITCH HALL EFFECT UNI 3-SIP |
| A1193LUA-T | IC SW HALL EFFECT CHOPPER 3SIP |
| A1203LUA-T | IC SW CONTINUOUS TIME BIPO 3-SIP |
| A1205EUA-T | IC SWITCH HALL EFFECT GP 3-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1181 | 制造商:Quick 功能描述:BQFP 19 X 19 NOZZLE FOR QUICK957/957D |
| A118-1 | 功能描述:SWITCH HARDWARE RoHS:是 類別:開關 >> 配件 - 帽蓋 系列:800 標準包裝:1 系列:AP 開關類型:按鈕 形狀:圓形，凸起（圓頂） 顏色:紅 發光:發光開口 適用于相關產品:AP 系列 安裝類型:卡入式 尺寸:12.35mm 直徑 x 6.25mm H 特點:- 配用:AP2N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N006SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N007SWBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125V更多... 其它名稱:*481D03001 |
| A1181ELHLT | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1181ELHLT-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1181EUA | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
發布緊急采購，3分鐘左右您將得到回復。