- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1645LK-I2 (Allegro Microsystems Inc)IC SENSOR HALL EFFECT AC 4-SIP Datasheet資料下載
參數資料
| 型號： | A1645LK-I2 |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 356K |
| 描述： | IC SENSOR HALL EFFECT AC 4-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 500 |
| 傳感范圍： | 120mV 跳閘，120mV 釋放 |
| 類型： | 專用型 |
| 電源電壓： | 4 V ~ 24 V |
| 電流 - 電源： | 8.4mA |
| 輸出類型： | 數字，開路集電極 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 散裝 |
Two-Wire True Zero-Speed Miniature Differential
Peak-Detecting Sensor IC with Continuous Calibration
A1642
4
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
OPERATING CHARACTERISTICS (continued) T
A
and V
CC
within speci cation, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min. Typ.
1
Max. Units
SWITCHPOINT CHARACTERISTICS
Operating Speed
f
OP
0 8,000 Hz
Analog Signal Bandwidth
BW Equivalent to f 3 dB
20 40 kHz
Operate Point
B
OP
Transitioning from I
CC(High)
to I
CC(Low)
; positive peak
referenced; AG < AG
MAX
120 mV
Release Point
B
RP
Transitioning from I
CC(Low)
to I
CC(High)
; negative peak
referenced; AG < AG
MAX
120 mV
CALIBRATION
Initial Calibration
C
I
Quantity of rising output (current) edges required for
accurate edge detection
3 Edge
DAC CHARACTERISTICS
Allowable User-Induced Differential
Offset
Operating within speci cation
?0 G
FUNCTIONAL CHARACTERISTICS
6
Operating Signal Range
7
Sig Operating within speci cation
30 1000 G
Minimum Operating Signal
Sig
OP(min)
Output switching (no missed edges); DC not
guaranteed
20 G
1
Typical values are at T
A
= 25癈 and V
CC
= 12 V. Performance may vary for individual units, within the speci ed maximum and minimum limits.
2
Maximum voltage must be adjusted for power dissipation and junction temperature; see Power Derating section.
3
Please refer to Device Operation section.
4
Power-On Time includes the time required to complete the internal automatic offset adjust. The DAC is then ready for peak acquisition.
5
dI is the difference between 10% of I
CC(Low)
and 90% of I
CC(High)
, and dt is the time period between those two points.
Note: dI/dt is dependent upon the value of the bypass capacitor, if one is used.
6
Functional characteristics valid only if magnetic offset is within the speci ed range for Allowable User Induced Differential Offset.
7
In order to remain in speci cation, the magnetic gradient must induce an operating signal greater than the minimum value speci ed. This includes the
effect of target wobble.
相關PDF資料 |
PDF描述 |
|---|---|
| A3230LUA-T | IC SW HALL EFFECT CHOPPER 3-SIP |
| A3241LUA-T | IC SWITCH HALL EFFECT 3-SIP |
| A3245LLHLT-T | IC SW HALL EFFECT OMNI SOT23W |
| A3251LUA-T | IC SW HALL EFFECT UNI 3-SIP |
| A3260LUA | IC SW HALL EFFECT BIPO 3-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A16486-02 | 制造商:LAIRD TECHNOLOGIES/ THE 功能描述:Tflex HR220 / 18 x 18 |
| A16486-03 | 制造商:LAIRD TECHNOLOGIES/ THE 功能描述:Tflex HR230 / 18 x 18 |
| A16486-04 | 制造商:LAIRD TECHNOLOGIES/ THE 功能描述:Tflex HR240 / 18 x 18 |
| A16486-05 | 制造商:LAIRD TECHNOLOGIES/ THE 功能描述:Tflex HR250 / 18 x 18 |
| A16486-06 | 制造商:LAIRD TECHNOLOGIES/ THE 功能描述:Tflex HR260 / 18 x 18 |
發布緊急采購，3分鐘左右您將得到回復。