- 您現在的位置：買賣IC網 > PDF目錄164966 > A165S-T3A-2 ROTARY SWITCH-3POSITIONS, DPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT PDF資料下載
參數資料
| 型號： | A165S-T3A-2 |
| 元件分類： | 開關 |
| 英文描述： | ROTARY SWITCH-3POSITIONS, DPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| 文件頁數： | 13/45頁 |
| 文件大小： | 1465K |
| 代理商： | A165S-T3A-2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
A16/M16
A16/M16
21
Installation
J
MOUNTING
After mounting the Pushbutton Unit to the panel, snap in the
Socket Unit from the back of the panel.
Panel mounting
Insert the Pushbutton Unit into the front of the panel, and fix the
lock ring and mounting nut from the terminal side.
Make sure that the lock ring is aligned with the thread of the case
and the edge of the lock ring is touching the panel.
Tighten the mounting nuts to a torque of 0.20 to 0.39 N m(3to
5kgf cm).
The maximum tightening torque is 0.39 N m(5kgf cm).
Case
Panel
Mounting nut
Lock ring
Edge
Thread
Switch Mounting
Snap on the Switch Unit to the Pushbutton Unit.
Make sure the the Switch Unit is in the proper orientation when
snapping on to the Pushbutton Unit.
J
SWITCH REMOVAL
Grip the part between the Switch holder of the case and the
Switch Unit using the A16Z-5080 Extractor, and pull to remove
the Switch Unit.
A16Z-5080 Extractor
J
REPLACEMENT PARTS
Removal and installation of the Operating Part
1. Remove the operating part as shown in the following
diagram. If the operating part cannot be removed by hand,
use the A3PJ-5080 Extractor.
Operating section
2. To attach the operating part, push until it clicks into place.
J
REMOVING THE LAMP
Removing from the Operating Part End
Grip theLampwiththe
A16Z-5080 Extractor and
pull to remove.
Lamp
Removing from the Switch Unit End
The Lamp can be removed by hand once the Switch is removed
using the A16Z-5080 Extractor.
J
INSTALLING THE LAMP
When mounting the Lamp, make sure it is facing the direction
shown in the following diagram. Insert the Lamp while matching
the protruding part of the Lamp and the small guides on the outer
surface of the case.
Protruding part
The Lamp can be mounted from the operating part end by using
the A16Z-5080 Extractor. The lamp can be mounted by following
the opposite procedure for removing the Lamp.
相關PDF資料 |
PDF描述 |
|---|---|
| A165W-T2AR-T2-2 | ROTARY SWITCH-2POSITIONS, DPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| A165W-J2MG-T2-2 | ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165W-J3MR-T2-2 | ROTARY SWITCH-3POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165W-T2MR-24D-1 | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165W-A2MY-24D-1 | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A165ST3A2Q | 制造商:Omron Corporation 功能描述: |
| A165ST3M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT ROUND ALT 3POS BLACK 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Selector Switch Round Operator |
| A165S-T3M | 功能描述:旋鈕開關 KNOB-TYPE RND 3POS MAINT SELECTOR SWCH RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
| A165ST3M2 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB RND 3-POS DPDT 制造商:Omron Electronic Components LLC 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A |
| A165S-T3M-2 | 功能描述:旋鈕開關 RND 3 PS MAINT KNOB IP65 DPDT RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
發布緊急采購，3分鐘左右您將得到回復。