- 您現在的位置：買賣IC網 > PDF目錄164966 > A165W-J3MR-T2-2 ROTARY SWITCH-3POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT PDF資料下載
參數資料
| 型號： | A165W-J3MR-T2-2 |
| 元件分類： | 開關 |
| 英文描述： | ROTARY SWITCH-3POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| 文件頁數： | 39/45頁 |
| 文件大小： | 1465K |
| 代理商： | A165W-J3MR-T2-2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁
M2BJ-B
M2BJ-B
45
Correct Use
J
NUT MOUNTING
Insert the buzzer unit from the front of the panel and tighten the
mounting nut inserted from the rear of the panel.
Since a projection exists on the rear portion of the buzzer unit, if
the mounting nut cannot be fitted into position, turn the nut
slightly.
The tightening torque of the mounting nut should be less than
5kg-cm.
Solder the terminals after mounting the nut. Otherwise, the
terminals, when thickened by solder, may prevent the nut from
being screwed down onto the buzzer unit.
J
MOUNTING
Tighten the mounting nut at a torque of less than 5 kg-cm.
J
WIRING
Exercise caution that the input terminals are not short-circuited
by the short-circuiting jumper.
Finish soldering within 5 seconds with a 30 watt soldering iron, or
within 3 seconds at a solder temperature of 240°C. For about a
minute after soldering, do not apply any force to the buzzer unit,
to avoid deforming the softened plastic buzzer unit base.
Use an non-corrosive, resin-based soldering flux.
J
SNAP-IN MOUNTING
Attach the mounting leaf spring to the buzzer. Engage the edges
of the leaf spring in the two grooves on the threaded section of
the buzzer. After inserting the leaf spring edges into the grooves,
confirm that the leaf spring has seated. Be sure to attach both
leaf springs.
Insert the buzzer assembly into the hole on the mounting panel
from the front.
J
SHORT-CIRCUITING JUMPER
The buzzer sounds continuously or intermittently depending on
how the short-circuiting bracket is attached to the case guide.
When the bracket is attached with the triangle on it facing
direction A (PC board side), the buzzer sounds intermittently.
To produce continuous sounds, attach the bracket to the case
guide so that the triangle on the bracket faces direction B.
相關PDF資料 |
PDF描述 |
|---|---|
| A165W-T2MR-24D-1 | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165W-A2MY-24D-1 | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165W-A2AR-24D-2 | ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165W-T2MG-24D-2 | ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165S-T2M-1 | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A165WJ3MY | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT RECT ALT 3POS YELLOW 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Selector Switch Rectangular Operator |
| A165W-J3MY | 功能描述:旋鈕開關 IL REC 3POS MAINT YELLOW SELECT SWCH RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
| A165WJ3MY24D2 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNB RECT 3POS DPDT ILL 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A |
| A165W-J3MY-24D-2 | 功能描述:旋鈕開關 REC 3PS MNT 24VD YLW IP65 DPDT Illum RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
| A165WJ3MY24D2OMA | 制造商:Omron Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。