欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: A22-HW-20A
元件分類: 開關
英文描述: PUSHBUTTON SWITCH, DPST, LATCHED, PANEL MOUNT
文件頁數: 35/48頁
文件大小: 1531K
代理商: A22-HW-20A
Common To All Assemblies
Common To All Assemblies
41
Installation
J
MOUNTING THE PANEL
Panel Hole Dimensions
22 dia.
(0.87)
25 dia.
(0.98)
24.1
(0.95)
22.3
(0.88)
22.3
(0.88)
25
(0.98)
3.2
(0.13)
For 25 mm-dia. holes, always use 25 mm-dia. Rings. (Since the
cutout dimensions are large, IP65 cannot be guaranteed unless
25-dia. Rings are used.)
If outer surface treatment such as paint is applied to the panel,
the panel dimensions after outer surface treatment must meet the
specified panel dimensions.
J
MATRIX INSTALLATION
1. The following panel hole dimensions apply when Switch Units
and the Standard-size Legend Plate Frame Lock Fitting are
mounted.
30
(1.18)
45
(1.77)
A22N-PR, -MR, -PX
A
22Z
30
(1.18)
41
(1.61)
2. The following panel hole dimensions apply when the
Large-size Legend Plate Frame is mounted.
45
(1.77)
45
(1.77)
A
22N-S
30
(1.18)
41
(1.61)
A
22Z
Locking should be applied toward the Engraving Plate.
Note: The above dimensions are the smallest-possible mounting
dimensions. However, these dimensions do not apply to
large Pushbutton Switches. For large Pushbutton
Switches, determine the distance between holes, taking
the Operational Unit and Legend Plate Frame into
account.
J
MOUNTING THE OPERATIONAL UNIT
ON THE PANEL
Insert the Operational Unit from the front surface of the panel,
insert the Lock Fitting and the mounting nut from the terminal
side, then tighten the nut. Before tightening, check that the rubber
washer is present between the Operational Unit and the panel.
When using a Legend Plate Frame, put one rubber washer each
between the Legend Plate Frame and the panel and between the
Operational Unit and the Legend Plate Frame. (One rubber
washer will be provided when one Legend Plate Frame is
ordered.)
Align the Lock Fitting with the groove in the casing, then insert
the Lock Fitting so that its edge is located on the panel side.
Tighten the mounting nut at a torque of 0.98 to 1.96 N m{10 to
20 kgf cm}.
When using a Lock Ring, replace with the supplied Lock Fitting,
insert the projecting part into the lock slot, and then tighten the
mounting nut.
Hold here
Mounting nut
Lock Fitting
Rubber washer
Panel
Proj-
ecting
part
Panel
Lock
Fitting
When the panel cutout dimension is 25 mm dia., remove the
supplied rubber washer and mount the 25 mm-dia. Ring as
shown below. (Since the A22Z-R25 is not attached to the main
body, order separately.)
Operational Unit
25-dia. Ring
Panel
Lock Fitting
Mounting nut
(A22Z-R25)
22.3 dia.
25 dia.
22.3 dia.
相關PDF資料
PDF描述
A22-SA-02M PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT
A22-TA-02M PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT
A22L-DY-6A-01A PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT
A22L-DY-T1-01M PUSHBUTTON SWITCH, SPST, MOMENTARY, PANEL MOUNT
A22L-HG-6D-10M PUSHBUTTON SWITCH, SPST, MOMENTARY, 6VDC, PANEL MOUNT
相關代理商/技術參數
參數描述
A22HW20AQ 制造商:Omron Corporation 功能描述:
A22HW20M 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NO 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O. DPST Round Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount
A22-HW-20M 功能描述:按鈕開關 DPST-NO MOM RND WHTE Half-guard actuator RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
A22HW20MQ 制造商:Omron Corporation 功能描述:
A22HY 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT PB ROUND/HALFGRD YEL 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Push Button Switch Round Half Guard Button
主站蜘蛛池模板: 深泽县| 龙门县| 长治县| 长乐市| 和林格尔县| 南漳县| 台东县| 武鸣县| 潞城市| 略阳县| 池州市| 克拉玛依市| 乌鲁木齐市| 绥德县| 万全县| 扶绥县| 巴楚县| 巢湖市| 延边| 浮山县| 政和县| 桂平市| 白水县| 寻甸| 延边| 泸定县| 永善县| 墨玉县| 乌兰察布市| 左贡县| 上思县| 石首市| 彭泽县| 关岭| 壤塘县| 呼和浩特市| 新竹县| 田东县| 凤山市| 沁阳市| 房产|