欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: A22-MY-10A
元件分類: 開關
英文描述: PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT
文件頁數: 38/48頁
文件大小: 1531K
代理商: A22-MY-10A
Common To All Assemblies
Common To All Assemblies
44
Removing the Switch Unit
Insert a screwdriver between the Mounting Latch and the Switch
Unit, then push down the screwdriver in the direction indicated by
the arrow in the following figure.
Use either of the following screwdrivers.
Flat-head
screwdriver
Screwdriver
Phillips
screwdriver
J
WIRING
Wiring Round Crimp Terminals
Loosen the terminal screw from the Switch Unit until it completely
comes off the groove, insert a screwdriver as shown in the following
figure, then push up the washer in the direction indicated by the
arrow to temporarily secure it. Now, a round crimp terminal can be
connected. After inserting the terminal, tighten the screws to com-
plete wiring.
Screw
Washer
Screwdriver
J
ENGRAVING
Engrave the characters on the surface on the Cap. Make sure
that the characters are aligned parallel to the imaginary line
connecting the two protruding portions to the left and right of the
Cap.
The characters must not be engraved deeper than 0.5 mm. Apply
an alcohol-based paint coating, such as melamine, alkyd, or
acrylic resin paint coating, to the engraved characters.
Protruding portions on Cap
J
AFFIXING CHARACTER FILM
Hold the Cap, remove the cardboard on the Film, and attach the Film
to the Cap. Make sure that the protruding portions of the Cap en-
gage the cutout portions of the Film and that the characters are
aligned parallel to the imaginary line connecting the two protruding
portions to the left and right of the Cap.
Protruding portions on Cap
Remove the cardboard.
J
MOUNTING AND DISMOUNTING
SNAP-IN LEGEND
Press and secure the Snap-in Legend Plate onto the Legend
Plate Frame.
The direction of the characters will vary with the mounting
direction of the control panel if the Switch is a knob or key
selector model.
Legend Plate Frame
Snap-in Legend Plate
Concave surface
相關PDF資料
PDF描述
A22-SR-20M PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT
A22L-DW-24A-20A PUSHBUTTON SWITCH, DPST, LATCHED, 24VDC, PANEL MOUNT
A22L-HG-6D-02M PUSHBUTTON SWITCH, DPST, MOMENTARY, 6VDC, PANEL MOUNT
A22L-TA-T1-01A PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT
A22L-DA-6A-01M PUSHBUTTON SWITCH, SPST, MOMENTARY, PANEL MOUNT
相關代理商/技術參數
參數描述
A22MY10M 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH SPST-NO 10A 110V 制造商:Omron Electronic Components LLC 功能描述:Switch Push Button N.O. SPST Mushroom Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O. SPST Mushroom Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount
A22-MY-10M 功能描述:按鈕開關 SPST-NO MOM RND YLW 40mm mushroom head RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
A22MY11A 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O./N.C. DPST Mushroom Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount
A22-MY-11A 功能描述:按鈕開關 SPST-NO+NC AL RND YL 40mm mushroom head RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
A22MY11M 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O./N.C. DPST Mushroom Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount
主站蜘蛛池模板: 温州市| 东阳市| 无为县| 会泽县| 海安县| 青铜峡市| 河北省| 浮山县| 沐川县| 大埔区| 海口市| 永州市| 长寿区| 时尚| 武义县| 丰原市| 房产| 阿克苏市| 苍南县| 浦城县| 南城县| 万安县| 潍坊市| 普兰店市| 清镇市| 三都| 确山县| 深泽县| 冷水江市| 黄浦区| 田林县| 聂荣县| 夏邑县| 陆丰市| 永登县| 威海市| 西畴县| 澄城县| 宜章县| 镇雄县| 仁布县|