欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: A22L-CW-T1-01A
元件分類: 開關
英文描述: PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT
文件頁數: 38/48頁
文件大小: 1531K
代理商: A22L-CW-T1-01A
Common To All Assemblies
Common To All Assemblies
44
Removing the Switch Unit
Insert a screwdriver between the Mounting Latch and the Switch
Unit, then push down the screwdriver in the direction indicated by
the arrow in the following figure.
Use either of the following screwdrivers.
Flat-head
screwdriver
Screwdriver
Phillips
screwdriver
J
WIRING
Wiring Round Crimp Terminals
Loosen the terminal screw from the Switch Unit until it completely
comes off the groove, insert a screwdriver as shown in the following
figure, then push up the washer in the direction indicated by the
arrow to temporarily secure it. Now, a round crimp terminal can be
connected. After inserting the terminal, tighten the screws to com-
plete wiring.
Screw
Washer
Screwdriver
J
ENGRAVING
Engrave the characters on the surface on the Cap. Make sure
that the characters are aligned parallel to the imaginary line
connecting the two protruding portions to the left and right of the
Cap.
The characters must not be engraved deeper than 0.5 mm. Apply
an alcohol-based paint coating, such as melamine, alkyd, or
acrylic resin paint coating, to the engraved characters.
Protruding portions on Cap
J
AFFIXING CHARACTER FILM
Hold the Cap, remove the cardboard on the Film, and attach the Film
to the Cap. Make sure that the protruding portions of the Cap en-
gage the cutout portions of the Film and that the characters are
aligned parallel to the imaginary line connecting the two protruding
portions to the left and right of the Cap.
Protruding portions on Cap
Remove the cardboard.
J
MOUNTING AND DISMOUNTING
SNAP-IN LEGEND
Press and secure the Snap-in Legend Plate onto the Legend
Plate Frame.
The direction of the characters will vary with the mounting
direction of the control panel if the Switch is a knob or key
selector model.
Legend Plate Frame
Snap-in Legend Plate
Concave surface
相關PDF資料
PDF描述
A22-FW-02M PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT
A22-GG-02M PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT
A22-GW-01A PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT
A22L-HA-24A-11M PUSHBUTTON SWITCH, SPST, MOMENTARY, 24VDC, PANEL MOUNT
A22L-HG-6A-20M PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT
相關代理商/技術參數
參數描述
A22LCWT101M 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH SPST-NC 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.C. SPST Square Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount
A22L-CW-T1-01M 功能描述:按鈕開關 SPST-NC MO SQ 110 WH IP65 LED Ill ext act RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
A22LCWT102A 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NC 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.C. DPST Square Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount
A22L-CW-T1-02A 功能描述:按鈕開關 DPST-NC AL SQ 110 WH IP65 LED Ill ext act RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
A22LCWT102M 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NC 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.C. DPST Square Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount
主站蜘蛛池模板: 略阳县| 邵阳县| 德江县| 赣州市| 新昌县| 皮山县| 太仓市| 台州市| 平陆县| 乐清市| 仁化县| 偃师市| 桦川县| 同江市| 曲麻莱县| 苗栗县| 分宜县| 会泽县| 大余县| 北碚区| 盐池县| 瓦房店市| 惠来县| 洛扎县| 连南| 突泉县| 定陶县| 剑阁县| 静宁县| 邵武市| 河南省| 葫芦岛市| 蛟河市| 紫云| 砚山县| 琼海市| 亳州市| 娱乐| 乐至县| 焦作市| 延庆县|