- 您現在的位置：買賣IC網 > PDF目錄164968 > A22L-HA-12A-11A PUSHBUTTON SWITCH, SPST, LATCHED, 12VDC, PANEL MOUNT PDF資料下載
參數資料
| 型號： | A22L-HA-12A-11A |
| 元件分類： | 開關 |
| 英文描述： | PUSHBUTTON SWITCH, SPST, LATCHED, 12VDC, PANEL MOUNT |
| 文件頁數： | 38/48頁 |
| 文件大小： | 1531K |
| 代理商： | A22L-HA-12A-11A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Common To All Assemblies
Common To All Assemblies
44
Removing the Switch Unit
Insert a screwdriver between the Mounting Latch and the Switch
Unit, then push down the screwdriver in the direction indicated by
the arrow in the following figure.
Use either of the following screwdrivers.
Flat-head
screwdriver
Screwdriver
Phillips
screwdriver
J
WIRING
Wiring Round Crimp Terminals
Loosen the terminal screw from the Switch Unit until it completely
comes off the groove, insert a screwdriver as shown in the following
figure, then push up the washer in the direction indicated by the
arrow to temporarily secure it. Now, a round crimp terminal can be
connected. After inserting the terminal, tighten the screws to com-
plete wiring.
Screw
Washer
Screwdriver
J
ENGRAVING
Engrave the characters on the surface on the Cap. Make sure
that the characters are aligned parallel to the imaginary line
connecting the two protruding portions to the left and right of the
Cap.
The characters must not be engraved deeper than 0.5 mm. Apply
an alcohol-based paint coating, such as melamine, alkyd, or
acrylic resin paint coating, to the engraved characters.
Protruding portions on Cap
J
AFFIXING CHARACTER FILM
Hold the Cap, remove the cardboard on the Film, and attach the Film
to the Cap. Make sure that the protruding portions of the Cap en-
gage the cutout portions of the Film and that the characters are
aligned parallel to the imaginary line connecting the two protruding
portions to the left and right of the Cap.
Protruding portions on Cap
Remove the cardboard.
J
MOUNTING AND DISMOUNTING
SNAP-IN LEGEND
Press and secure the Snap-in Legend Plate onto the Legend
Plate Frame.
The direction of the characters will vary with the mounting
direction of the control panel if the Switch is a knob or key
selector model.
Legend Plate Frame
Snap-in Legend Plate
Concave surface
相關PDF資料 |
PDF描述 |
|---|---|
| A22-MY-10A | PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT |
| A22-SR-20M | PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT |
| A22L-DW-24A-20A | PUSHBUTTON SWITCH, DPST, LATCHED, 24VDC, PANEL MOUNT |
| A22L-HG-6D-02M | PUSHBUTTON SWITCH, DPST, MOMENTARY, 6VDC, PANEL MOUNT |
| A22L-TA-T1-01A | PUSHBUTTON SWITCH, SPST, LATCHED, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A22LHA12A11M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST 10A 110V |
| A22L-HA-12A-11M | 功能描述:按鈕開關 SPST-NO+NC RN 12V BL IP65 LED full-guard RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| A22LHA12A20A | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NO 10A 110V |
| A22L-HA-12A-20A | 功能描述:按鈕開關 DPST-NO AL RN 12V BL IP65 LED full-guard RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| A22LHA12A20M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NO 10A 110V |
發布緊急采購，3分鐘左右您將得到回復。