- 您現在的位置：買賣IC網 > PDF目錄373916 > AD7787BRM-REEL (ANALOG DEVICES INC) Low Power, 2-Channel 24-Bit Sigma-Delta ADC PDF資料下載
參數資料
| 型號： | AD7787BRM-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Low Power, 2-Channel 24-Bit Sigma-Delta ADC |
| 中文描述： | 2-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO10 |
| 封裝： | MO-187BA, MSOP-10 |
| 文件頁數： | 10/20頁 |
| 文件大小： | 326K |
| 代理商： | AD7787BRM-REEL |
AD7787
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip registers, which are described on the following pages. In the following
descriptions,
set
implies a Logic 1 state and
cleared
implies a Logic 0 state, unless otherwise noted.
Rev. 0 | Page 10 of 20
COMMUNICATIONS REGISTER (RS1, RS0 = 0, 0)
The communications register is an 8-bit write-only register. All communications to the part must start with a write operation to the
communications register. The data written to the communications register determines whether the next operation is a read or write
operation and to which register this operation takes place. For read or write operations, once the subsequent read or write operation to the
selected register is complete, the interface returns to where it expects a write operation to the communications register. This is the default
state of the interface and, on power-up or after a reset, the ADC is in this default state waiting for a write operation to the communications
register. In situations where the interface sequence is lost, a write operation of at least 32 serial clock cycles with DIN high returns the
ADC to this default state by resetting the entire part. Table 5 outlines the bit designations for the communications register. CR0 through
CR7 indicate the bit location, CR denoting the bits are in the communications register. CR7 denotes the first bit of the data stream. The
number in the parenthesis indicates the power-on/reset default status of that bit.
CR7
WEN (0)
CR6
0 (0)
CR5
RS1 (0)
CR4
RS0 (0)
CR3
R/W (0)
CR2
CREAD (0)
CR1
CH1 (0)
CR0
CH0 (0)
Table 5. Communications Register Bit Designations
Bit
Location
Name
Description
CR7
WEN
Write Enable Bit. A 0 must be written to this bit so that the write to the communications register actually occurs. If a
1 is the first bit written, the part does not clock on to subsequent bits in the register. It stays at this bit location until
a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits are loaded to the communications
register.
CR6
0
This bit must be programmed to Logic 0 for correct operation.
CR5 to
CR4
RS0
this serial interface communication (see Table 6).
CR3
R/W
A 0 in this bit location indicates that the next operation is a write to a specified register. A 1 in this position indicates
that the next operation is a read from the designated register.
CR2
CREAD
Continuous Read of the Data Register. When this bit is set to 1 (and the data register is selected), the serial interface
is configured so that the data register can be continuously read, i.e., the contents of the data register are placed on
the DOUT pin automatically when the SCLK pulses are applied. The communications register does not have to be
written to for data reads. To enable continuous read mode, the instruction 00111100 (Channel AIN1) or 00111101
(Channel AIN2) must be written to the communications register. To exit the continuous read mode, the instruction
001110XX must be written to the communications register while the RDY pin is low. While in continuous read
mode, the ADC monitors activity on the DIN line so that it can receive the instruction to exit continuous read mode.
Additionally, a reset occurs if 32 consecutive 1s are seen on DIN. Therefore, DIN should be held low in continuous
read mode until an instruction is to be written to the device.
CR1 to
CR0
CH0
(AIN1()/AIN1()) can be selected. Alternatively, the power supply can be selected, i.e., the ADC can measure the
voltage on the power supply, which is useful for monitoring power supply variation. To perform this measurement,
the power supply voltage is divided by 5 and then applied to the modulator for conversion. The ADC uses a
1.17 V ± 5% on-chip reference as the reference source when this channel is selected. Any change in channel
resets the filter and a new conversion is started.
Bit
RS1 to
Register Address Bits. These address bits are used to select which of the ADC’s registers are being selected during
CH1 to
These bits are used to select the analog input channel. Channel AIN1 or AIN2 can be selected or an internal short
Table 6. Register Selection
RS1
RS0
0
0
0
0
0
1
1
0
1
1
Register
Communications Register during a Write Operation
Status Register during a Read Operation
Mode Register
Filter Register
Data Register
Register Size
8-Bit
8-Bit
8-Bit
8-Bit
24-Bit
相關PDF資料 |
PDF描述 |
|---|---|
| AD7787 | Low Power, 2-Channel 24-Bit Sigma-Delta ADC |
| AD7789 | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788 | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788ARM | Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788ARM-REEL | Low Power, 16-/24-Bit Sigma-Delta ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7787BRMZ | 功能描述:IC ADC 24BIT 2CH LP SIG 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7787BRMZ | 制造商:Analog Devices 功能描述:IC 24BIT ADC SMD 7787 MSOP10 |
| AD7787BRMZ-RL | 功能描述:IC ADC 24BIT 2CH LP SIG 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7788 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 16-/24-Bit Sigma-Delta ADC |
| AD7788ARM | 功能描述:IC ADC 16BIT SIGMA-DELTA 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。