- 您現在的位置：買賣IC網 > PDF目錄373918 > AD7828UQ (ANALOG DEVICES INC) LC2MOS High Speed 4- & 8-Channel 8-Bit ADCs PDF資料下載
參數資料
| 型號： | AD7828UQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | LC2MOS High Speed 4- & 8-Channel 8-Bit ADCs |
| 中文描述： | 8-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP28 |
| 封裝： | 0.600 INCH, CERDIP-28 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 270K |
| 代理商： | AD7828UQ |
AD7824/AD7828
REV. F
–9–
MODE 0
Figure 14 shows the timing diagram for Mode 0 operation. This
mode can only be used for microprocessors that have a WAIT
state facility, whereby a READ instruction cycle can be extended
to accommodate slow memory devices. A READ operation brings
CS
and
RD
low, which starts a conversion. The analog multiplexer
address inputs must remain valid while
CS
and
RD
are low. The
data bus (DB7–DB0) remains in the three-state condition until
conversion is complete. There are two converter status outputs on
the AD7824/AD7828, interrupt (
INT
) and ready (RDY), which
can be used to drive the microprocessor READY/WAIT input.
The RDY is an open-drain output (no internal pull-up device) that
goes low on the falling edge of
CS
and goes high impedance at the
end of conversion when the 8-bit conversion result appears on the
data outputs. If the RDY status is not required, the external
pull-up resistor can be omitted and the RDY output tied to GND.
The
INT
goes low when conversion is complete and returns high
on the rising edge of
CS
or
RD
.
MODE 1
Mode 1 operation is designed for applications where the micropro-
cessor is not forced into a WAIT state. A READ operation takes
CS
and
RD
low, which triggers a conversion (see Figure 15). The
multiplexer address inputs are latched on the rising edge of
RD
.
Data from the previous conversion is read from the three-state
data outputs (DB7–DB0). This data may be disregarded if not
required. Note that the RDY output (open drain output) does
not provide any status information in this mode and must be
connected to GND. At the end of conversion,
INT
goes low. A
second READ operation is required to access the new conversion
result. This READ operation latches a new address into the multi-
plexer inputs and starts another conversion.
INT
returns high at the
end of the second READ operation, when
CS
or
RD
returns high.
A delay of 2.5
μ
s must be allowed between READ operations.
CS
RD
ANALOG
CHANNEL
ADDRESS
RDY
INT
DATA
t
CSS
t
AS
t
RDY
t
CRD
t
ACC2
t
DH
t
INTH
t
AH
t
AS
t
P
t
CSS
t
CSH
ADDRESS
VALID
ADDRESS
VALID
DATA
VALID
HIGH IMPEDANCE
Figure 14. Mode 0 Timing Diagram
CS
RD
ANALOG
CHANNEL
ADDRESS
INT
DATA
t
CSS
t
AS
ADDRESS
VALID
OLD
VALID
ADDRESS
VALID
NEW
VALID
t
CSH
t
AH
t
RD
t
CRD
t
INTH
t
ACC1
t
DH
t
ACC1
t
DH
t
INTH
t
AH
t
AS
t
P
t
CSS
t
RD
t
CSH
Figure 15. Mode 1 Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD7824BQ | 1.2V, 12 Bit 200KSPS, Serial ADC 6-SOT-23 -40 to 85 |
| AD7828LRS | LC2MOS High Speed 4- & 8-Channel 8-Bit ADCs |
| AD7834 | 14-Bit Quad DAC(14位四D/A轉換器) |
| AD7835 | 14-Bit Quad DAC(14位四D/A轉換器) |
| AD7837AR | LC2MOS Complete, Dual 12-Bit MDACs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7828UQ/883 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single-Ended Data Acquisition System |
| AD7828UQ/883B | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS High Speed 4- & 8-Channel 8-Bit ADCs |
| AD7829 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 2 MSPS, 8-Bit, 1-, 4-, 8-Channel Sampling ADCs |
| AD7829-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 2 MSPS, 8-Bit, 8-Channel ADC |
| AD7829BN | 制造商:Analog Devices 功能描述:ADC Single Semiflash 2Msps 8-bit Parallel 28-Pin PDIP W 制造商:Rochester Electronics LLC 功能描述:8-CHNL 2MSPS PARALLEL 8-BIT ADC I.C. - Bulk 制造商:Analog Devices 功能描述:IC 8BIT ADC 7829 DIP28 |
發布緊急采購，3分鐘左右您將得到回復。