- 您現在的位置：買賣IC網 > PDF目錄373920 > AD7858LAN (ANALOG DEVICES INC) 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC PDF資料下載
參數資料
| 型號： | AD7858LAN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| 中文描述： | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP24 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-24 |
| 文件頁數： | 12/32頁 |
| 文件大?。?/td> | 315K |
| 代理商： | AD7858LAN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
REV. B
–12–
AD7858/AD7858L
MSB
ZERO
BUSY
SGL/
DIFF
CH2
CH1
CH0
PMGT1
PMGT0
RDSLT1
RDSLT0
2/
3
MODE
X
CALMD
CALSLT1
CALSLT0
STCAL
LSB
STATUS REGISTER BIT FUNCTION DESCRIPTION
Bit
Mnemonic
Comment
15
14
ZERO
BUSY
This bit is always 0.
Conversion/Calibration Busy Bit. When this bit is 1, it indicates that there is a conversion
or calibration in progress. When this bit is 0, there is no conversion or calibration in progress.
These four bits indicate the channel selected for conversion (see Table III).
13
12
11
10
9
8
7
6
5
SGL/
DIFF
CH2
CH1
CH0
PMGT1
PMGT0
RDSLT1
RDSLT0
2/
3
MODE
Power management bits. These bits along with the
SLEEP
pin will indicate if the part is in a
power-down mode or not. See Table VI for description.
Both of these bits are always 1, indicating it is the status register being read (see Table II).
Interface Mode Select Bit. With this bit at 0, the device is in Interface Mode 2. With this bit at
1, the device is in Interface Mode 1. This bit is reset to 0 after every read cycle.
Don
’
t care bit.
Calibration Mode Bit. A 0 in this bit indicates a self-calibration is selected, and a 1 in this bit
indicates a system calibration is selected (see Table IV).
Calibration Selection Bits and Start Calibration Bit. The STCAL bit is read as a 1 if a
calibration is in progress and as a 0 if there is no calibration in progress. The CALSLT1 and
CALSLT0 bits indicate which of the calibration registers are addressed for reading and writing
(see section on the Calibration Registers for more details).
4
3
X
CALMD
2
1
0
CALSLT1
CALSLT0
STCAL
STATUS REGISTER
The arrangement of the Status Register is shown below. The status register is a read-only register and contains 16 bits of data. The
status register is selected by first writing to the control register and putting two 1s in RDSLT1 and RDSLT0. The function of the bits
in the status register are described below. The power-up status of all bits is 0.
START
WRITE TO CONTROL REGISTER
SETTING RDSLT0 = RDSLT1 = 1
READ STATUS REGISTER
Figure 6. Flowchart for Reading the Status Register
相關PDF資料 |
PDF描述 |
|---|---|
| AD7858LAR | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858LBN | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858LBR | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858L* | 3 V to 5 V Single Supply. 200 kSPS 8-Channel. 12-Bit Sampling ADC |
| AD7862AR-2 | Simultaneous Sampling Dual 250 kSPS 12-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7858LAN3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858LANZ | 功能描述:IC ADC 12BIT 8CHAN SRL 24DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7858LAR | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Serial 24-Pin SOIC W |
| AD7858LAR3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| AD7858LAR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Serial 24-Pin SOIC W T/R |
發布緊急采購，3分鐘左右您將得到回復。