- 您現在的位置：買賣IC網 > PDF目錄373921 > AD7863ARS-2 (ANALOG DEVICES INC) Simultaneous Sampling Dual 175 kSPS 14-Bit ADC PDF資料下載
參數資料
| 型號： | AD7863ARS-2 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Simultaneous Sampling Dual 175 kSPS 14-Bit ADC |
| 中文描述： | 4-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | MO-150AH, SSOP-28 |
| 文件頁數： | 10/18頁 |
| 文件大?。?/td> | 207K |
| 代理商： | AD7863ARS-2 |
AD7863
–
10
–
REV. A
Gain error can be adjusted at either the first code transition (ADC
negative full scale) or the last code transition (ADC positive full
scale). The trim procedures for both cases are as follows:
Positive Full-Scale Adjust (-10 Version)
Apply a voltage of +9.9927 V (FS/2
–
1 LSBs) at V
1
. Adjust R2
until the ADC output code flickers between 01 1111 1111 1110
and 01 1111 1111 1111.
Negative Full-Scale Adjust (-10 Version)
Apply a voltage of
–
9.9976 V (
–
FS + 1 LSB) at V
1
and adjust
R2 until the ADC output code flickers between 10 0000 0000
0000 and 10 0000 0000 0001.
An alternative scheme for adjusting full-scale error in systems
that use an external reference is to adjust the voltage at the V
REF
pin until the full-scale error for any of the channels is adjusted
out. The good full-scale matching of the channels will ensure
small full-scale errors on the other channels.
TIMING AND CONTROL
Figure 5a shows the timing and control sequence required to
obtain optimum performance (Mode 1) from the AD7863. In
the sequence shown, a conversion is initiated on the falling edge
of
CONVST
. This places both track/holds into hold simulta-
neously and new data from this conversion is available in the
output register of the AD7863 5.2
μ
s later. The BUSY signal
indicates the end of conversion and at this time the conversion
results for both channels are available to be read. A second
conversion is then initiated. If the multiplexer select A0 is low,
the first and second read pulses after the first conversion ac-
cesses the result from Channel A (V
A1
and V
A2
respectively).
The third and fourth read pulses, after the second conversion
and A0 high, accesses the result from Channel B (V
B1
and V
B2
respectively). A0
’
s state can be changed any time after the
CONVST
goes high, i.e., track/holds into hold and 500 ns prior
to the next falling edge of
CONVST
. Note that A0 should not
be changed during conversion if the nonselected channels have
negative voltages applied to them which are outside the input
range of the AD7863, as this will affect the conversion in
progress. Data is read from the part via a 14-bit parallel data bus
with standard
CS
and
RD
signal, i.e., the read operation con-
sists of a negative going pulse on the
CS
pin combined with two
negative going pulses on the
RD
pin (while the
CS
is low),
accessing the two 14-bit results. Once the read operation has
taken place, a further 400 ns should be allowed before the next
falling edge of
CONVST
to optimize the settling of the track/
hold amplifier before the next conversion is initiated. The
achievable throughput rate for the part is 5.2
μ
s (conversion
time) plus 100 ns (read time) plus 0.4
μ
s (quiet time). This
results in a minimum throughput time of 5.7
μ
s (equivalent to a
throughput rate of 175 kHz).
Read Options
Apart from the Read Operation described above and displayed
in Figure 5a, other
CS
and
RD
combinations can result in dif-
ferent channels/inputs being read in different combinations.
Suitable combinations are shown in Figures 5b through 5d.
CS
RD
DATA
V
A1
V
A2
Figure 5b. Read Option A (A0 Is Low)
CS
RD
DATA
V
A1
V
A2
V
A1
Figure 5c. Read Option B (A0 Is Low)
t
3
t
5
t
4
V
A1
V
A2
V
B1
V
B2
CONVST
BUSY
A0
CS
RD
DATA
t
1
t
7
t
2
t
6
t
CONV
= 5.2 s
t
ACQ
t
8
Figure 5a. Mode 1 Timing Operation Diagram for High Sampling Performance
相關PDF資料 |
PDF描述 |
|---|---|
| AD7863ARS-3 | Simultaneous Sampling Dual 175 kSPS 14-Bit ADC |
| AD7863AR-2 | RECTIFIER SCHOTTKY DUAL 30A 60V 275A-ifsm 0.7V-vf 1mA-ir TO-3P 30/TUBE |
| AD7863AR-3 | RECTIFIER SCHOTTKY DUAL 40A 40V 375A-ifsm 0.58V-vf 1mA-ir TO-3P 30/TUBE |
| AD7864AS-1 | VARISTOR 150V RMS 20MM RADIAL |
| AD7864BS-1 | SWITCH SLIDE DP3T RT ANG L=6MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7863ARS-2REEL | 功能描述:IC ADC 14BIT DUAL 2CH 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7863ARS-2REEL7 | 功能描述:IC ADC 14BIT DUAL 2CH 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7863ARS-3 | 功能描述:IC ADC 14BIT DUAL 2CH 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7863ARS-3REEL | 功能描述:IC ADC 14BIT DUAL 2CH 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7863ARS-3REEL7 | 功能描述:IC ADC 14BIT DUAL 2CH 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發(fā)布緊急采購，3分鐘左右您將得到回復。