欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7865AS-2
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: Four-Channel, Simultaneous Sampling, Fast, 14-Bit ADC
中文描述: 4-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP44
封裝: PLASTIC, QFP-44
文件頁數: 8/19頁
文件大小: 195K
代理商: AD7865AS-2
AD7865
–8–
REV. A
TERMINOLOGY
Signal to (Noise + Distortion) Ratio
This is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (f
S
/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the quan-
tization noise. The theoretical signal to (noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by:
Signal to
(
Noise
+
Distortion
) = (6.02
N
+ 1.76)
dB
Thus for a 14-bit converter, this is 86.04dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7865 it is defined as:
THD dB
V
V
V
V
V
)
=
+
+
+
+
20
22
32
42
52
62
1
log
V
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
and
V
5
are the rms amplitudes of the second through the fifth
harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to f
S
/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it will be a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
±
nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for which
neither m nor n are equal to zero. For example, the second
order terms include (fa + fb) and (fa – fb), while the third order
terms include (2 fa + fb), (2 fa – fb), (fa + 2 fb) and (fa – 2 fb).
The AD7865 is tested using two input frequencies. In this case,
the second and third order terms are of different significance.
The second order terms are usually distanced in frequency from
the original sine waves, while the third order terms are usually at
a frequency close to the input frequencies. As a result, the sec-
ond and third order terms are specified separately. The calcula-
tion of the intermodulation distortion is as per the THD speci-
fication where it is the ratio of the rms sum of the individual
distortion products to the rms amplitude of the fundamental
expressed in dBs.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale 10kHz sine wave signal to one channel and a 50 kHz
signal to another channel and measuring how much of that
signal is coupled onto the first channel. The figure given is the
worst case across all four channels of the AD7865.
Relative Accuracy
Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
Differential Nonlinearity
This is the difference between the measured and the ideal
1LSB change between any two adjacent codes in the ADC.
Positive Gain Error (AD7865-1, AD7865-3)
This is the deviation of the last code transition (01. . . 110 to
01 . . . 111) from the ideal 4
×
V
REF
– 3/2 LSB (AD7865 at
±
10 V), 2
×
V
REF
– 3/2 LSB (AD7865 at
±
5 V range) or
V
REF
– 3/2 LSB (AD7865 at
±
2.5 V range), after the Bipolar
Offset Error has been adjusted out.
Positive Gain Error (AD7865-2)
This is the deviation of the last code transition (111. . . 110 to
111 . . . 111) from the ideal 2
×
V
REF
– 3/2 LSB (AD7865 at
0 V to +5 V), V
REF
– 3/2 LSB (AD7865 at 0 V to +2.5 V)
after the Unipolar Offset Error has been adjusted out.
Unipolar Offset Error (AD7865-2)
This is the deviation of the first code transition (000 . . . 000 to
000 . . . 001) from the ideal AGND + 1/2 LSB.
Bipolar Zero Error (AD7865-1, AD7865-3)
This is the deviation of the midscale transition (all 0s to 1s)
from the ideal AGND – 1/2 LSB.
Negative Gain Error (AD7865-1, AD7865-3)
This is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal –4
×
V
REF
+ 1/2 LSB (AD7865 at
±
10 V), –2
×
V
REF
+ 1/2 LSB (AD7865 at
±
5 V range) or
–V
REF
+ 1/2 LSB (AD7865 at
±
2.5 V range), after Bipolar Zero
Error has been adjusted out.
Track/Hold Acquisition Time
Track/Hold acquisition time is the time required for the out-
put of the track/hold amplifier to reach its final value, within
±
1/2 LSB, after the end of conversion (the point at which the
track/hold returns to track mode). It also applies to situations
where there is a step input change on the input voltage applied
to the selected V
INxA
/V
INxB
input of the AD7865. It means that
the user must wait for the duration of the track/hold acquisition
time after the end of conversion or after a step input change to
V
INxA
/V
INxB
before starting another conversion, to ensure that
the part operates to specification.
相關PDF資料
PDF描述
AD7865AS-3 Four-Channel, Simultaneous Sampling, Fast, 14-Bit ADC
AD7865BS-1 Four-Channel, Simultaneous Sampling, Fast, 14-Bit ADC
AD7865BS-2 Four-Channel, Simultaneous Sampling, Fast, 14-Bit ADC
AD7865BS-3 Four-Channel, Simultaneous Sampling, Fast, 14-Bit ADC
AD7866ARU Dual 1 MSPS, 12-Bit, 2-Channel SAR ADC with Serial Interface
相關代理商/技術參數
參數描述
AD7865AS-2REEL 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 14-bit Parallel 44-Pin MQFP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 350KSPS 14BIT PARALLEL 44MQFP - Tape and Reel
AD7865AS-3 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 14-bit Parallel 44-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:4 CH. SIMULTANEOUS BIPOLAR,14-B ADC I.C. - Bulk 制造商:Analog Devices 功能描述:IC 14-BIT ADC
AD7865AS-3REEL 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 14-bit Parallel 44-Pin MQFP T/R
AD7865ASZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Four-Channel, Simultaneous Sampling, Fast, 14-Bit ADC
AD7865ASZ-1 功能描述:IC ADC 14BIT DUAL 4CH 44-MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
主站蜘蛛池模板: 津南区| 泰兴市| 上蔡县| 洪雅县| 彩票| 电白县| 威宁| 昌图县| 蒙城县| 崇州市| 霍山县| 乐业县| 上栗县| 遵化市| 永昌县| 兰西县| 乌鲁木齐县| 沅陵县| 建始县| 施甸县| 静海县| 阆中市| 关岭| 清镇市| 五指山市| 观塘区| 漳浦县| 鄂托克前旗| 葵青区| 东港市| 泰来县| 莫力| 天祝| 新巴尔虎右旗| 涿鹿县| 双城市| 嘉黎县| 淳化县| 博野县| 基隆市| 台东市|