欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7870SQ
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs
中文描述: 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, CDIP24
封裝: 0.300 INCH, HERMETIC SEALED, CERDIP-24
文件頁數: 15/20頁
文件大小: 331K
代理商: AD7870SQ
REV. B
2
AD7870/AD7875/AD7876
–15–
ST AND-ALONE OPE RAT ION
T he AD7870/AD7875/AD7876 can be used in its Mode 2, par-
allel interface mode for stand-alone operation. In this case, con-
version is initiated with a pulse to the ADC
CS
input. T his
pulse must be longer than the conversion time of the ADC. T he
BUSY
output is used to drive the
RD
input. Data is latched
from the ADC DB0–DB11 outputs to an external latch on the
rising edge of
BUSY
.
Figure 25. Stand-Alone Operation
APPLICAT ION HINT S
Good printed circuit board (PCB) layout is as important as the
overall circuit design itself in achieving high speed A/D perfor-
mance. T he designer has to be conscious of noise both in the
ADC itself and in the preceding analog circuitry. Switching
mode power supplies are not recommended as the switching
spikes will feed through to the comparator causing noisy code
transitions. Other causes of concern are ground loops and digi-
tal feedthrough from microprocessors. T hese are factors which
influence any ADC, and a proper PCB layout which minimizes
these effects is essential for best performance.
LAY OUT HINT S
Ensure that the layout for the printed circuit board has the digi-
tal and analog signal lines separated as much as possible. T ake
care not to run any digital track alongside an analog signal track.
Guard (screen) the analog input with AGND.
Establish a single point analog ground (star ground) separate
from the logic system ground at the AGND pin or as close as
possible to the ADC. Connect all other grounds and the
AD7870/AD7875/AD7876 DGND to this single analog ground
point. Do not connect any other digital grounds to this analog
ground point.
Low impedance analog and digital power supply common re-
turns are essential to low noise operation of the ADC, so make
the foil width for these tracks as wide as possible. T he use of
ground planes minimizes impedance paths and also guards the
analog circuitry from digital noise. T he circuit layout of Figures
30 and 31 have both analog and digital ground planes which are
kept separated and only joined together at the AD7870/
AD7875/AD7876 AGND pin.
NOISE
K eep the input signal leads to V
IN
and signal return leads from
AGND as short as possible to minimize input noise coupling. In
applications where this is not possible, use a shielded cable be-
tween the source and the ADC. Reduce the ground circuit im-
pedance as much as possible since any potential difference in
grounds between the signal source and the ADC appears as an
error voltage in series with the input signal.
DAT A ACQUISIT ION BOARD
Figure 28 shows the AD7870/AD7875/AD7876 in a data acqui-
sition circuit. T he corresponding printed circuit board (PCB)
layout and silkscreen are shown in Figures 29 to 31. T he board
layout has three interface ports: one serial and two parallel. One
of the parallel ports is directly compatible with the ADSP-2100
evaluation board expansion connector.
T he only additional component required for a full data acquisi-
tion system is an antialiasing filter. A component grid is pro-
vided near the analog input on the PCB, which may be used for
such a filter or any other input conditioning circuitry. T o facili-
tate this option there is a shorting plug (labelled LK 1 on the
PCB) on the analog input track. If this shorting plug is used, the
analog input connects to the buffer amplifier driving the ADC;
if this shorting plug is omitted, a wire link can be used to con-
nect the analog input to the PCB component grid.
INT E RFACE CONNE CT IONS
T here are two parallel connectors labeled SK T 4 and SK T 6 and
one serial connector labeled SK T 5. A shorting plug option
(LK 3 in Figure 28) on the ADC 12/
8
/CLK input configures
the ADC for the appropriate interface (see Pin Function
Description).
SK T 6 is a 96-contact (3-ROW) Eurocard connector that is
directly compatible with the ADSP-2100 Evaluation Board
Prototype Expansion Connector. T he expansion connector on
the ADSP-2100 has eight decoded chip enable outputs labeled
ECE1
to
ECE8
.
ECE6
is used to drive the ADC
CS
input on
the data acquisition board. T o avoid selecting on board RAM
sockets at the same time, LK 6 on the ADSP-2100 board must
be removed. In addition, the ADSP-2100 expansion connector
has four interrupts labelled
EIRQ0
to
EIRQ3
. T he ADC
BUSY
/
INT
output connects to
EIRQ0
. T here is a single wait state gen-
erator connected to EDMACK to allow the ADC to interface to
the faster versions of the ADSP-2100.
SK T 4 is a 26-way (2-ROW) IDC connector. T his connector
contains all the signal contacts as SK T 6 with the exception of
EDMACK which is connected to SK T 6 only. It also contains
decoded R/
W
and
STRB
inputs which are necessary for
T MS32020 interfacing. T he SK T 4 pinout is shown in Fig-
ure 26.
Figure 26. SKT4, IDC Connector Pinout
相關PDF資料
PDF描述
AD7870TQ LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs
AD7876CN 16-Bit, Pseudo Bipolar, Fully Diff Input, 250kSPS Serial Out, 2.7V to 5.5V Micro Power Sampling ADC 8-MSOP -40 to 85
AD7876CQ 16-Bit, Pseudo Bipolar, Fully Diff Input, 250kSPS Serial Out, 2.7V to 5.5V Micro Power Sampling ADC 8-MSOP -40 to 85
AD7876CR 16-Bit, Pseudo Bipolar, Fully Diff Input, 250kSPS Serial Out, 2.7V to 5.5V Micro Power Sampling ADC 8-MSOP -40 to 85
AD7876TQ 16-Bit, Pseudo Bipolar, Fully Diff Input, 250kSPS Serial Out, 2.7V to 5.5V Micro Power Sampling ADC 8-MSOP -40 to 85
相關代理商/技術參數
參數描述
AD7870SQ/883B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter, 12-Bit
AD7870SQQ10 制造商:Analog Devices 功能描述:
AD7870TE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog to Digital Converter
AD7870TE/883B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter, 12-Bit
AD7870TQ 功能描述:模數轉換器 - ADC 12-Bit 100kHz Sampling RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
主站蜘蛛池模板: 城步| 永州市| 水城县| 广平县| 定远县| 凤庆县| 和田市| 历史| 东丽区| 大埔区| 卓尼县| 金山区| 武清区| 安顺市| 靖安县| 桃园市| 公安县| 抚州市| 泽库县| 射洪县| 阿巴嘎旗| 泾阳县| 衡山县| 高碑店市| 垦利县| 钟祥市| 皋兰县| 兴国县| 报价| 沾化县| 宜良县| 汾西县| 阜阳市| 樟树市| 博兴县| 鄂伦春自治旗| 金坛市| 栖霞市| 多伦县| 喀什市| 马山县|