- 您現在的位置：買賣IC網 > PDF目錄373922 > AD7873ARQ (ANALOG DEVICES INC) 10-Bit, 60 MSPS ADC SE/Diff, Int/Ext Ref., program. i/p range w/Pwrdown, comp. to ADS822/4/5/6/8 28-SSOP PDF資料下載
參數資料
| 型號： | AD7873ARQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | 10-Bit, 60 MSPS ADC SE/Diff, Int/Ext Ref., program. i/p range w/Pwrdown, comp. to ADS822/4/5/6/8 28-SSOP |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO16 |
| 封裝： | 0.150 INCH, MO-137AB, QSOP-16 |
| 文件頁數： | 20/28頁 |
| 文件大小： | 657K |
| 代理商： | AD7873ARQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7873
Table 7. Power Management Options
PD1 PD0 PENIRQ
0
0
Enabled
Rev. D | Page 20 of 28
Description
This configuration results in immediate power-down of the on chip reference as soon as PD1 is set to 0. The ADC
powers down only between conversions. When PD0 is set to 0, the conversion is performed first and the ADC
powers down upon completion of that conversion (or upon the rising edge of CS if it occurs first). At the start of
the next conversion, the ADC instantly powers up to full power. This means if the device is being used in the
differential mode, or an external reference is used, there is no need for additional delays to ensure full operation
and the very first conversion is valid. The Y– switch is on while in power-down. When the device is performing
differential table conversions, the reference and reference buffer do not attempt to power up with Bits PD1 and
PD0 programmed in this way.
This configuration results in switching the reference off immediately and the ADC on permanently. When the
device is performing differential tablet conversions, the reference and reference buffer do not attempt to power
up with bits PD1 and PD0 programmed in this way.
This configuration results in switching the reference on and powering the ADC down between conversions. The
ADC powers down only between conversions. When PD0 is set to 0, the conversion is performed first, and the
ADC powers down upon completion of the conversion (or upon the rising edge of CS if it occurs first). At the start
of the next conversion, the ADC instantly powers up to full power. There is no need for additional delays to
ensure full operation as the reference remains permanently powered up.
Disabled This configuration results in always keeping the device powered up. The reference and the ADC are on.
0
1
Enabled
1
0
Enabled
1
1
POWER VS. THROUGHPUT RATE
By using the power-down options on the AD7873 when not
converting, the average power consumption of the device
decreases at lower throughput rates. Figure 35 shows how, as the
throughput rate is reduced while maintaining the DCLK
frequency at 2 MHz, the device remains in its power-down state
longer and the average current consumption over time drops
accordingly.
S
μ
A
1
100
10
1000
0
120
THROUGHPUT (kSPS)
0
40
60
20
80
100
f
DCLK
= 16
×
f
SAMPLE
f
DCLK
= 2MHz
V
CC
= 2.7V
T
A
= –40°C TO +85°C
Figure 35. Supply Current vs. Throughput (μA)
For example, if the AD7873 is operated in a 24 DCLK continuous
sampling mode, with a throughput rate of 10 kSPS and a DCLK
of 2 MHz, and the device is placed in the power-down mode
between conversions, (PD0, PD1 = 0, 0), that is, the ADC shuts
down between conversions but the reference remains powered
down permanently, then the current consumption is calculated
as follows. The current consumption during normal operation
with a 2 MHz DCLK is 210 μA (V
CC
= 2.7 V). Assuming an
external reference is used, the power-up time of the ADC is
instantaneous, so when the part is converting, it consumes
210 μA. In this mode of operation, the part powers up on the
fourth falling edge of DCLK after the start bit is recognized. It
goes back into power-down at the end of conversion on the
20th falling edge of DCLK, which means that the part consumes
210 μA for 16 DCLK cycles only, 8 μs during each conversion
cycle. If the throughput rate is 10 kSPS, the cycle time is 100 μs
and the average power dissipated during each cycle is (8/100) ×
(210 μA) = 16.8 μA.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7873ARU | Touch Screen Digitizer |
| AD7873ARUZ | Touch Screen Digitizer |
| AD7873BCP | Touch Screen Digitizer |
| AD7873BRQ | Touch Screen Digitizer |
| AD7874 | 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System(LC2MOS 4通道,12位同時采樣DAS) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7873ARQ-REEL | 制造商:Analog Devices 功能描述:TOUCH SCREEN DIGITIZER 制造商:Rochester Electronics LLC 功能描述:2.7V 12-BIT TOUCH SCREEN DIGITIZER I.C. - Tape and Reel |
| AD7873ARQ-REEL7 | 制造商:Analog Devices 功能描述:TOUCH SCREEN DIGITIZER 制造商:Analog Devices 功能描述:2.7V 12-BIT TOUCH SCREEN DIGITIZER I.C. - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:2.7V 12-BIT TOUCH SCREEN DIGITIZER I.C. - Tape and Reel |
| AD7873ARQZ | 功能描述:IC ADC 12BIT TOUCHSCREEN 16QSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7873ARQZ-REEL | 功能描述:IC ADC 12BIT TOUCHSCREEN 16QSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7873ARQZ-REEL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 16QSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。