欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7878LP
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: IC LOGIC 125 LOW-VOLTAGE SINGLE FET 8-OHM BUS SWITCH -40+85C SC-70-5 3000/REEL
中文描述: 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC28
封裝: PLASTIC, LCC-28
文件頁數: 13/16頁
文件大小: 417K
代理商: AD7878LP
AD7878
–13–
REV. A
Establish a single point analog ground (star ground) separate
from the logic system ground at Pin 22 (AGND) or as dose as
possible to the AD7878, as shown in Figure 22. Connect all
other grounds and Pin 7 (AD7878 DGND) to this single analog
ground point. Do not connect any other digital grounds to this
analog ground point. Low impedance analog and digital power
supply common returns are essential to low noise operation of
the ADC, so make the foil width for these tracks as wide as
possible. The use of ground planes minimizes impedance paths
and also guards the analog circuitry from digital noise. The
circuit layouts of Figures 25 and 26 have both analog and digital
ground planes, which are kept separated and only joined to-
gether at the AD7878 AGND pin.
NOISE
Keep the input signal leads to V
IN
and signal return leads from
AGND (Pin 22) as short as possible to minimize input noise
coupling. In applications where this is not possible, use a
shielded cable between the source and the ADC. Reduce the
ground circuit impedance as much as possible since any poten-
tial difference in grounds between the signal source and the
ADC appears as an error voltage in series with the input signal.
Figure 22. Power Supply Grounding Practice
DATA ACQUISITION BOARD
Figure 23 shows the AD7878 in a data acquisition circuit that
will interface directly to either the ADSP-2100, TMS32010 or
the TMS32020. The corresponding printed circuit board (PCB)
layout and silkscreen are shown in Figures 24 to 26.
The only additional component required for a full data acquisi-
tion system is an antialiasing filter. There is a component grid
provided near the analog input on the PCB which may be used
for such a filter or any other conditioning circuitry. To facilitate
this option, a wire link (labelled LK1 on the PCB) is required
on the analog input track. This link connects the input signal to
either the component grid or directly to the buffer amplifier
driving the AD7878 analog input.
Microprocessor connections to the PCB can be made by either
of two ways:
1. 96-contact (3 ROW) Eurocard connector.
2. 26-contact (2 ROW) IDC connector.
The 96-contact Eurocard connector is directly compatible with
the ADSP-2100 Evaluation Board Prototype Expansion Con-
nector. The expansion connector on the ADSP-2100 has eight
decoded drip enable outputs labelled
ECE8
to
ECE1
.
ECE6
is
used to drive the AD7878
CS
input on the data acquisition
board. To avoid selecting onboard RAM sockets at the same
time, LK6 on the ADSP-2100 board must be removed. In addi-
tion, the expansion connector on the ADSP-2100 has four inter-
rupts labelled
EIRQ3
to
EIRQ0
. The AD7878
ALFL
output
connects to
EIRQ0
. The AD7878 and ADSP-2100 data lines
are
aligned for left justified data transfer.
The 26-way IDC connector contains all the necessary contacts
for both the TMS32010 and TMS32020. There are two
switches on the data acquisition board that must be set to en-
able the appropriate interface configuration (see Table III). The
interface connections for the TMS32010/32020 and IDC signal
contact numbers are shown in Table IV and Figure 23. Note the
AD7878 CS input must be decoded from the address bus prior
to the AD7878 evaluation board for the TMS320XX interfaces.
Connections to the analog input (V
IN
) and the
CONVST
input
are made via two BNC sockets labelled SKT1 and SKT2 on the
silkscreen. If the
CONVST
input is derived from either the
microprocessor or ADC clock, the effects of clock noise cou-
pling will be reduced.
Table III. AD7878 PCB Switch Settings
SWITCH SETTING
Microprocessor
SW1
SW2
ADSP-2100
TMS32010
TMS32020
A
B
B
A
A
B
POWER SUPPLY CONNECTIONS
The PCB requires two analog supplies and one 5 V digital sup-
ply. Connections to the analog supplies are made directly to the
PCB as shown on the silk screen in Figure 24. The connections
are labelled V+ and V– and the range for both of these supplies
is 12 V to 15 V. Connection to the 5 V digital supply is made
through either of the two microprocessor connectors. The +5 V
and –5 V analog power supplies required by the AD7878 are
generated from two voltage regulators on the V+ and V– power
supply inputs (IC3 and IC4 in Figure 23).
COMPONENT LIST
IC1
IC2
AD711 Op Amp
AD7878 Analog-to-Digital
Converter
MC78L05 5 V Regulator
MC79L05 –5 V Regulator
74HC00 Quad NAND Gate
74HC04 Hex Inverter
74HC02 Quad NOR Gate
Single Pole Double Throw
Double Pole Double Throw
Wire Link for Analog Input
10
μ
F Capacitors
IC3
IC4
IC5*
IC6*
IC7
SW1
SW2
LK1
C1, C3, C5, C7, C9
C11, C13, C15
C2, C4, C6, C8, C10
C12, C14, C16
R1*, R2*
SKT1, SKT2
SKT3
0.1
μ
F Capacitors
10 k
Resistors
BNC Sockets
26-Contact (2 Row) IDC
Connector
96-Contact (3 Row) Eurocard
Connector
SKT4
*Not required for ADSP-2100 Interface.
相關PDF資料
PDF描述
AD7878JN LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7878JP LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7880 Enclosed Switches Series LS: Rod - Adjustable; 1NC 1NO DPDT Snap Action, Double Break; 0.5 in - 14NPT conduit; Plug-in
AD7880CR LC2MOS Single +5 V Supply, Low Power, 12-Bit Sampling ADC
AD7880BN LC2MOS Single +5 V Supply, Low Power, 12-Bit Sampling ADC
相關代理商/技術參數
參數描述
AD7878LPZ 功能描述:IC ADC 12BIT W/DSP INT 28-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率(每秒):1.8M 數據接口:并聯 轉換器數目:1 功率耗散(最大):1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP(7x7) 包裝:管件 輸入數目和類型:2 個單端,單極
AD7878LPZ-REEL 功能描述:IC ADC 12BIT W/DSP 28PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD7878SE 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7878SE/883B 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12-BIT ADC IC - Bulk 制造商:Analog Devices 功能描述:CONVERTER - ADC
AD7878SQ 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 12-BIT PARALLEL 28CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk 制造商:Analog Devices 功能描述:IC ADC 12BIT W/DSP INT 28-CDIP 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC COMPLETE 12 BIT ADC IC 制造商:Analog Devices 功能描述:CONVERTER - ADC
主站蜘蛛池模板: 涿鹿县| 张家港市| 襄城县| 长葛市| 墨脱县| 仙游县| 乌拉特后旗| 建湖县| 郁南县| 枣庄市| 特克斯县| 太康县| 金乡县| 高清| 房山区| 马公市| 绍兴县| 巴中市| 辉县市| 独山县| 林周县| 桐乡市| 申扎县| 金门县| 胶州市| 长葛市| 隆子县| 米脂县| 黄平县| 信宜市| 辽中县| 永兴县| 界首市| 塘沽区| 道孚县| 宝坻区| 北海市| 昭通市| 潜山县| 临湘市| 军事|