欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7878SQ
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: IC 1:10 CLOCK DRIVER 20-QSOP
中文描述: 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDIP28
封裝: HERMETIC SEALED, CERDIP-28
文件頁數: 10/16頁
文件大小: 417K
代理商: AD7878SQ
AD7878
–10–
REV. A
CONVERSION TIMING
The track-and-hold on the AD7878 goes from track-to-hold
mode on the rising edge of
CONVST
, and the value of V
IN
at
this point is the value which will be converted. However, the
conversion actually sorts on the next rising edge of CLK IN
after
CONVST
goes high. If
CONVST
goes high within ap-
proximately 30 ns prior to a rising edge of CLK IN, that CLK
IN edge will not be seen as the first CLK IN edge of the con-
version process, and conversion will not actually start until one
CLK IN cycle later. As a result, the conversion time (from
CONVST
to FIFO update) will vary by one clock cycle de-
pending on the relationship between
CONVST
and CLK IN.
A conversion cycle normally consists of 56 CLK IN cycles
(assuming no read/write operations) which corresponds to a 7
As conversion time. If
CONVST
goes high within 30 ns prior
to a rising edge of CLK IN, the conversion time will consist of
57 CLK IN cycles, i.e., 7.125
μ
s. This effect does not cause
track/hold jitter.
INTERNAL REFERENCE
The AD7878 has an on-chip temperature compensated buried
Zener reference (see Figure 14) that is factory trimmed to 3 V
±
1%. Internally, it provides both the DAC reference and the
dc bias required for bipolar operation. The reference output is
available (REF OUT) and is capable of providing up to 500
μ
A
to an external load.
Figure 14. AD7878 Reference Circuit
The maximum recommended capacitance on REF OUT for
normal operation is 50 pF. If the reference is required for use
external to the AD7878, it should be decoupled with a
200
resistor in series with a parallel combination of a 10
μ
F
tantalum capacitor and a 0.1
μ
F ceramic capacitor. These
decoupling components are required to remove voltage spikes
caused by the internal operation of the AD7878.
TRACK-AND-HOLD AMPLIFIER
The track-and-hold amplifier on the analog input of the
AD7878 allows the ADC to accurately convert an input sine
wave of 6 V peak-peak amplitude to 12-bit accuracy. The input
bandwidth of the track/hold amplifier is much greater than the
Nyquist rate of the ADC even when operated at its minimum
conversion time. The 0.1 dB cutoff frequency occurs typically
at 500 kHz. The track/hold amplifier acquires an input signal to
12-bit accuracy in less than 2
μ
s.
The operation of the track/hold amplifier is transparent to the
user. The track/hold amplifier goes from its tracking mode to
its hold mode at the start of conversion on the rising edge of
CONVST
and returns to track mode at the end of conversion.
ANALOG INPUT
Figure 15 shows the AD7878 analog input. The analog input
range is
±
3 V into an input resistance of typically 15 k
. The
designed code transitions occur midway between successive
integer LSB values (i.e., 1/2 LSB, 3/2 LSBs, 5/2 LSBs . . . .
FS–3/2 LSBs). The output code is 2s complement binary with
1 LSB = FS/4096 = 6 V/4096 = 1.46 mV. The ideal input/
output transfer function is shown in Figure 16.
Figure 15. AD7878 Analog Input
Figure 16. Input/Output Transfer Function
OFFSET AND FULL-SCALE ADJUSTMENT
In most Digital Signal Processing (DSP) applications offset and
full-scale error have little or no effect on system performance.
Offset error can always be eliminated in the analog domain by
ac coupling. Full-scale error effect is linear and does not cause
problems as long as the input signal is within the full dynamic
range of the ADC. Some applications may require that the input
signal span the full analog input dynamic range and, accord-
ingly, offset and full-scale error will have to be adjusted to zero.
Where adjustment is required, offset must be adjusted before
full-scale error. This is achieved by trimming the offset of the
op amp driving the analog input of the AD7878 while the input
voltage is 1/2 LSB below ground. The trim procedure is as
follows: apply a voltage of –0.73 mV (–1/2 LSB) at V
1
and
adjust the op amp offset voltage until the ADC output code
flickers between 1111 1111 1111 and 0000 0000 0000.
Gain error can be adjusted at either the first code transition
(ADC negative full scale) or the last code transition (ADC
positive full scale). The trim procedures for both cases are as
follows:
相關PDF資料
PDF描述
AD7878 LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7878AQ LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7878BQ LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7878KN LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7878KP LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
相關代理商/技術參數
參數描述
AD7878SQ/883B 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin CDIP 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 12-BIT PARALLEL 28CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12-BIT ADC IC - Bulk 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC COMPLETE 12-BIT ADC IC
AD7879 制造商:Analog Devices 功能描述:LOW COST CONTROLLER FOR TOUCH SCREENS - Rail/Tube
AD7879-1ACBZ-500R7 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Voltage Controller for Touch Screens
AD7879-1ACBZ-RL 制造商:Analog Devices 功能描述:
AD7879-1ACPZ-500R7 功能描述:IC ADC 12BIT CTRLR TOUCH 16LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
主站蜘蛛池模板: 阿克苏市| 南宫市| 桑植县| 三河市| 云南省| 甘肃省| 阳东县| 霞浦县| 吴忠市| 临湘市| 廊坊市| 兴文县| 娱乐| 五大连池市| 罗江县| 迭部县| 交城县| 宣威市| 兴义市| 桐庐县| 焦作市| 宁德市| 濮阳县| 周宁县| 舒城县| 望奎县| 读书| 三河市| 竹北市| 前郭尔| 丹凤县| 巨野县| 沈阳市| 酉阳| 年辖:市辖区| 普洱| 连江县| 德令哈市| 泰和县| 西乡县| 泰兴市|