- 您現在的位置：買賣IC網 > PDF目錄373923 > AD7887 (Analog Devices, Inc.) +2.7 V to +5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead uSOIC PDF資料下載
參數資料
| 型號： | AD7887 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | +2.7 V to +5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead uSOIC |
| 中文描述： | 2.7 V至5.25 V，微功耗，2通道，125 kSPS的，12位ADC的8引腳uSOIC |
| 文件頁數： | 12/16頁 |
| 文件大小： | 133K |
| 代理商： | AD7887 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁
REV. B
AD7887
–12–
Mode 3 (PM1 = 1, PM0 = 0)
In this mode, the AD7887 automatically enters its full shutdown
mode at the end of every conversion. It is similar to Mode 1
except that the status of
CS
does not have any effect on the
power-down status of the AD7887.
Figure 15a shows the general diagram of the operation of the
AD7887 in this mode. On the first falling SCLK edge after
CS
goes low, all on-chip circuitry starts to power up. It takes ap-
proximately, 5
μ
s for the AD7887 internal circuitry to be fully
powered up. As a result, a conversion (or sample-and-hold
acquisition) should not be initiated during this 5
μ
s. T he input
signal is sampled on the second rising edge of SCLK following
the
CS
falling edge. T he user should ensure that 5
μ
s elapses
between the first falling edge of
SCLK
and the second rising
edge of SCLK after the
CS
falling edge as shown in Figure 15a.
In microcontroller applications (or with a slow serial clock) this
is readily achievable by driving the
CS
input from one of the
port lines and ensuring that the serial data read (from the micro-
controller’s serial port) is not initiated for 5
μ
s. However, for
higher speed serial clocks it will not be possible to have a 5
μ
s
delay between powering up and the first rising edge of the SCLK .
T herefore, the user will need to write to the Control Register to
exit this mode and (by writing PM1 = 0 and PM0 = 1) put the
part into Mode 2. A second conversion will then need to be
initiated when the part is powered up to get a conversion result, as
shown in Figure 15b. T he write operation that takes place in
conjunction with this second conversion can put the part back
into Mode 3 and the part will go into power-down mode when
the conversion sequence ends.
Mode 4 (PM1 = 1, PM0 = 1)
In this mode, the AD7887 automatically enters a standby (or
sleep) mode at the end of every conversion. In this standby
mode, all on-chip circuitry, apart from the on-chip reference, is
powered down. T his mode is similar to Mode 3 but in this case,
the power-up time is much shorter as the on-chip reference
remains powered up at all times.
Figure 16 shows the general diagram of the operation of the
AD7887 in this mode. On the first falling SCLK edge after
CS
goes low, the AD7887 comes out of standby. T he AD7887
wake-up time is very short in this mode so it is possible to wake-
up the part and carry out a valid conversion in the same read/
write operation. T he input signal is sampled on the second
rising edge of SCLK following the
CS
falling edge. At the end of
conversion (last rising edge of SCLK ) the part automatically
enters its standby mode.
SCLK
CS
DOUT
DIN
THE PART POWERS UP FROM
SHUTDOWN ON SCLK FALLING EDGE AS
PM1 = 1 AND PM0 = 0
1
16
1
16
2
t
10
= 5
m
s
THE PART ENTERS
SHUTDOWN AT THE END OF
CONVERSION AS PM1 = 1 AND PM0 = 0
CONTROL REGISTER DATA IS LOADED ON THE
FIRST 8 CLOCKS. PM1 = 1 AND PM0 = 0
PM1 = 1 AND PM0 = 0 TO KEEP THE
PART IN THIS MODE
DATA IN
DATA IN
4 LEADING ZEROS + CONVERSION RESULT
4 LEADING ZEROS + CONVERSION RESULT
Figure 15a. Mode 3 Operation
SCLK
CS
DOUT
DIN
1
16
8
1
16
8
1
16
8
PM1 = 0 AND PM0 = 1 TO PLACE
THE PART IN NORMAL MODE
PM1 = 1 AND PM0 = 0 TO PLACE
THE PART BACK IN MODE 3
CONTROL REGISTER DATA IS LOADED ON
THE FIRST 8 CLOCKS. PM1 = 1 AND PM0 = 0
THE PART ENTERS
SHUTDOWN AT THE END
OF CONVERSION AS
PM1 = 1 AND PM0 = 0
THE PART REMAINS POWERED UP
AS PM1 = 0 AND PM0 = 1
THE PART BEGINS TO POWER
UP FROM SHUTDOWN
THE PART ENTERS
SHUTDOWN AT THE END OF
CONVERSION AS PM1 = 1
AND PM0 = 0
4 LEADING ZEROS
+ CONVERSION RESULT
DATA IN
4 LEADING ZEROS
+ CONVERSION RESULT
DATA IN
4 LEADING ZEROS
+ CONVERSION RESULT
DATA IN
Figure 15b. Mode 3 Operation
相關PDF資料 |
PDF描述 |
|---|---|
| AD7887AR | +2.7 V to +5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead uSOIC |
| AD7887ARM | +2.7 V to +5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead uSOIC |
| AD7887BR | +2.7 V to +5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead uSOIC |
| AD7888(中文) | 2.7 V to 5.25 V, Micro Power, 8-Channel,125kSPS,12-Bit ADC(微功耗,125kSPS,8通道12位A/D轉換器) |
| AD7888 | +2.7 V to +5.25 V, Micropower, 8-Channel, 125 kSPS, 12-Bit ADC in 16-Lead TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7887AR | 功能描述:IC ADC 12BIT 2CH SRL 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7887ARM | 功能描述:IC ADC 12BIT 2CH SRL 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7887ARM-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 125ksps 12-bit Serial 8-Pin MSOP T/R |
| AD7887ARM-REEL7 | 功能描述:IC ADC 12BIT 2CH SRL 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7887ARMZ | 功能描述:IC ADC 12BIT 2CH SRL 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。