欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

<pre id="aocqs"></pre>

<strike id="aocqs"></strike>

收藏本站

您好，
買賣IC網歡迎您。
請登錄
免費注冊

您現在的位置：買賣IC網 > PDF目錄373925 > AD7904 (Analog Devices, Inc.) 4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP PDF資料下載

參數資料

型號：	AD7904
廠商：	Analog Devices, Inc.
元件分類：	ADC
英文描述：	4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP
中文描述：	4通道，1 MSPS的，8-/10-/12-Bit ADC的16與序列鉛TSSOP封裝
文件頁數：	13/24頁
文件大小：	411K
代理商：	AD7904

第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁

AD7904/AD7914/AD7924

–13–

REV. 0

Table I. Control Register Bit Functions

MSB

WRITE

LSB

CODING

SEQ1 DONTC

DONTC

ADD1 ADD0

PM1

PM0

SEQ0

DONTC

RANGE

Bit

Mnemonic

Comment

WRITE

The value written to this bit of the Control Register determines whether the following 11 bits will be loaded

to the control register or not. If this bit is a 1 then the following 11 bits will be written to the control register; if it

is a 0 then the remaining 11 bits are not loaded to the control register and so it remains unchanged.

The SEQ1 bit in the control register is used in conjunction with the SEQ0 bit to control the use of the

sequencer function. (See Table IV.)

SEQ1

9–8

7–6

DONTCARE

ADD1, ADD0 These two address bits are loaded at the end of the present conversion sequence and select which analog

input channel is to be converted in the next serial transfer, or they may select the final channel in a consecutive

sequence as described in Table IV. The selected input channel is decoded as shown in Table II. The

address bits corresponding to the conversion result are also output on DOUT prior to the 12 bits of data,

see the Serial Interface section. The next channel to be converted on will be selected by the mux on the

fourteenth SCLK falling edge.

PM1, PM0

Power Management Bits. These two bits decode the mode of operation of the AD7904/AD7914/AD7924

as shown in Table III.

SEQ0

The SEQ0 bit in the control register is used in conjunction with the SEQ1 bit to control the use of the

sequencer function. (See Table IV.)

DONTCARE

RANGE

This bit selects the analog input range to be used on the AD7904/AD7914/AD7924. If it is set to 0 then the

analog input range will extend from 0 V to 2

REF

. If it is set to 1 then the analog input range will extend

from 0 V to REF

(for the next conversion). For 0 V to 2

REF

, V

= 4.75 V to 5.25 V.

CODING

This bit selects the type of output coding the AD7904/AD7914/AD7924 will use for the conversion result.

If this bit is set to 0 the output coding for the part will be twos complement. If this bit is set to 1 then the

output coding from the part will be straight binary (for the next conversion).

5, 4

CODE

1.0

4096

–0.4

–0.8

–1.0

0.2

–0.2

–0.6

2048

0.6

= V

= 5V

TEMP = 25 C

0.4

0.8

2560

3072

3584

512

1024

1536

TPC 6. AD7924 Typical INL

CONTROL REGISTER

The Control Register on the AD7904/AD7914/AD7924 is a 12-bit, write-only register. Data is loaded from the DIN pin of the

AD7904/AD7914/AD7924 on the falling edge of SCLK. The data is transferred on the DIN line at the same time that the conver-

sion result is read from the part. The data transferred on the DIN line corresponds to the AD7904/AD7914/AD7924 configuration

for the next conversion. This requires 16 serial clocks for every data transfer. Only the information provided on the first 12 falling

clock edges (after

falling edge) is loaded to the Control Register. MSB denotes the first bit in the data stream. The bit functions

are outlined in Table I.