- 您現在的位置：買賣IC網 > PDF目錄373926 > AD7912AUJ-R2 (ANALOG DEVICES INC) 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs PDF資料下載
參數資料
| 型號： | AD7912AUJ-R2 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs |
| 中文描述： | 2-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | MO-193BA, TSOT-8 |
| 文件頁數： | 18/32頁 |
| 文件大小： | 386K |
| 代理商： | AD7912AUJ-R2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7912/AD7922
MODES OF OPERATION
The three modes of operation of the AD7912/AD7922 are
normal mode, power-down mode, and daisy-chain mode. The
mode of operation is selected by controlling the logic state of
the CS signal. The point at which CS is pulled high after the
conversion has been initiated determines whether the
AD7912/AD7922 enter power-down mode or change to daisy-
chain mode. Similarly, if already in daisy-chain mode, CS can
control whether the device returns to normal operation or
enters power-down mode. The user can also change from daisy-
chain mode to normal mode by writing to the DIN pin, as
outlined in the DIN Input section.
Rev. 0 | Page 18 of 32
Power-down mode is designed to provide flexible power
management options and to optimize the ratio of power
dissipation to throughput rate for different application
requirements.
Daisy-chain mode is intended for applications where fast
throughput rate is not required and more than one
AD7912/AD7922 have been connected in a daisy chain, as
shown in Figure 33.
NORMAL MODE
Normal mode is intended for the fastest throughput rate
performance. The user does not have to worry about any
power-up time, because the AD7912/AD7922 remain fully
powered all the time. Figure 26 shows the operation of the
AD7912/AD7922 in this mode.
The conversion is initiated on the falling edge of CS as
described in the Serial Interface section. To ensure that the part
remains fully powered up at all times, CS must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
of CS. If CS is brought high after the 10th SCLK falling edge
and before the 12th SCLK falling edge, then the device enters
daisy-chain mode, as shown in Figure 27. The conversion is
terminated and DOUT goes back into three-state. If CS is
brought high after the 13th SCLK falling edge, but before the
end of t
CONVERT
, the conversion is terminated and DOUT goes
back into three-state, but the part remains in normal mode.
For the AD7922, 16 serial clock cycles are required to complete
the conversion and access the complete conversion result. For
the AD7912, a minimum of 14 serial clock cycles are required
to complete the conversion and access the complete
conversion result.
CS can idle high until the next conversion or can idle low until
CS returns high sometime prior to the next conversion
(effectively idling CS low). Once a data transfer is complete
(DOUT has returned to three-state), another conversion can be
initiated after the quiet time, t
QUIET
, has elapsed by bringing CS
low again.
POWER-DOWN MODE
Power-down mode is intended for use in applications where
slower throughput rates are required. Either the ADC is
powered down between each conversion, or a series of
conversions can be performed at a high throughput rate and
then the ADC is powered down for a relatively long duration
between these bursts of several conversions. When the AD7912/
AD7922 are in power-down mode, all analog circuitry is
powered down.
To enter power-down mode, the conversion process must be
interrupted by bringing CS high any time after the second
falling edge of SCLK and before the 10th falling edge of SCLK,
as shown in Figure 28. Once CS has been brought high in this
window of SCLKs, then the part enters power-down mode, the
conversion that was initiated by the falling edge of CS is termi-
nated, and DOUT goes back into three-state. If CS is brought
high before the second SCLK falling edge, then the part remains
in normal mode and does not power down. This helps to avoid
accidental power-down due to glitches on the CS line.
To exit this mode of operation and power the AD7912/AD7922
up again, a dummy conversion is performed. On the falling edge
of CS, the device begins to power up and continues to power up
as long as CS is held low until after the falling edge of the
10th SCLK. The device is fully powered up once 16 SCLKs have
elapsed and valid data results from the next conversion, as
shown in Figure 29. If CS is brought high before the 10th falling
edge of SCLK, then the AD7912/AD7922 go back into power-
down mode. This helps to avoid accidental power-up due to
glitches on the CS line or an inadvertent burst of 8 SCLK cycles
while CS is low. Therefore, although the device might begin to
power up on the falling edge of CS, it powers down again on the
rising edge of CS, as long as this occurs before the 10th SCLK
falling edge.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7922AUJ-REEL7 | Circular Connector; No. of Contacts:7; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:16S; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle |
| AD7912AUJ-REEL7 | Circular Connector; No. of Contacts:5; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:16S; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:16S-8 RoHS Compliant: No |
| AD7912 | 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs |
| AD7912ARM | 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs |
| AD7912ARM-REEL | 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7912AUJ-REEL7 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AD7912AUJZ-REEL | 功能描述:IC ADC 10BIT DUAL 2CH TSOT-23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7912AUJZ-REEL7 | 功能描述:IC ADC 10BIT DUAL 2CH TSOT-23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7914 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP |
| AD7914BRU | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 10-bit Serial 16-Pin TSSOP 制造商:Analog Devices 功能描述:IC 10BIT ADC SMD 7914 TSSOP16 |
發布緊急采購，3分鐘左右您將得到回復。