欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7912AUJ-REEL7
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: Circular Connector; No. of Contacts:5; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:16S; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:16S-8 RoHS Compliant: No
中文描述: 2-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8
封裝: MO-193BA, TSOT-8
文件頁數: 17/32頁
文件大小: 386K
代理商: AD7912AUJ-REEL7
AD7912/AD7922
Table 7 provides some typical performance data with various
op amps used as the input buffer, and a 50 kHz input tone under
the same setup conditions.
Table 7. AD7922 Performance for Various Input Buffers
Op Amp in the Input
Buffer
50 kHz Input , V
DD
= 3.6 V
Single op amps
AD8038
72.79
AD8510
72.35
AD8021
72.2
Dual op amps
AD712
72.68
AD8022
72.88
Rev. 0 | Page 17 of 32
AD7922 SNR Performance (dB)
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum
source impedance depends on the amount of total harmonic
distortion (THD) that can be tolerated. The THD increases as
the source impedance increases and performance degrades (see
Figure 16).
DIGITAL INPUTS
The digital inputs applied to the AD7912/AD7922 are not
limited by the maximum ratings that limit the analog input.
Instead, the digital inputs applied can go to 7 V and are not
restricted by the V
DD
+ 0.3 V limit as on the analog input. For
example, if the AD7912/AD7922 are operated with a V
DD
of 3 V,
then 5 V logic levels could be used on the digital inputs. How-
ever, it is important to note that the data output on DOUT still
has 3 V logic levels when V
DD
= 3 V. Another advantage of
SCLK, DIN, and CS not being restricted by the V
DD
+ 0.3 V limit
is that power supply sequencing issues are avoided. If CS, DIN,
or SCLK are applied before V
DD
, then there is no risk of latch-up
as there would be on the analog inputs if a signal greater than
0.3 V were applied prior to V
DD
.
DIN INPUT
The channel to be converted on in the next conversion is
selected by writing to the DIN pin. Data on the DIN pin is
loaded into the AD7912/AD7922 on the falling edge of SCLK.
The data is transferred into the part on the DIN pin at the same
time that the conversion result is read from the part. Only the
third and fourth bits of the DIN word are used; the rest are
ignored by the ADC.
The third MSB is the channel identifier bit, which identifies the
channel to be converted on in the next conversion,
V
IN0
(CHN = 0) or V
IN1
(CHN = 1).
The fourth MSB, STY, is related to the mode of operation of the
device. To keep the AD7912/ AD7922 in daisy-chain mode, the
CHN and STY bits have to be inverted during the conversions
(STY ≠ CHN). A conversion with STY = CHN on the input
forces the device to normal mode in the next cycle. See the
Daisy-Chain Mode section for more details.
If the AD7912/AD7922 are not going to be used in daisy-chain
mode, it is recommended to keep STY and CHN the same
(STY = CHN). In that case, the channel can be selected by tying
DIN either high or low during a conversion cycle.
To summarize:
CHN = 0
, Channel 0 selected for next conversion.
CHN = 1
, Channel 1 selected for next conversion.
CHN = STY
, forces normal mode in the next cycle.
CHN
STY
, keeps the AD7912/AD7922 in daisy-chain mode.
0
LSB
MSB
X
X
CHN
STY
DON'T CARE
Figure 24. AD7912/AD7922 DIN Word
DOUT OUTPUT
The conversion result from the AD7912/AD7922 is provided on
this output as a serial data stream. The bits are clocked out on
the SCLK falling edge at the same time that the conversion is
taking place.
The serial data stream for the AD7922 consists of two leading
zeros followed by the bit that identifies the channel converted,
the bit that indicates the current mode of operation, and the
12-bit conversion result with MSB provided first.
For the AD7912, the serial data stream consists of two leading
zeros followed by the bit that identifies the channel converted,
the bit that indicates the current mode of operation, and the
10-bit conversion result with MSB provided first, followed by
two trailing zeros.
The CHN and MOD bits on DOUT indicate to the user the
current mode of operation of the ADC. If CHN = MOD,
the AD7912/AD7922 are in normal mode. Otherwise, if
CHN ≠ MOD, the AD7912/AD7922 are in daisy-chain mode.
0
LSB
AD7912
MSB
0
0
0
0
CHN
MOD CONVERSION RESULT
AD7922
0
0
CHN
MOD
CONVERSION RESULT
Figure 25. AD7912/AD7922 DOUT Word
相關PDF資料
PDF描述
AD7912 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs
AD7912ARM 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs
AD7912ARM-REEL 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs
AD7912ARM-REEL7 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs
AD7922 2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs
相關代理商/技術參數
參數描述
AD7912AUJZ-REEL 功能描述:IC ADC 10BIT DUAL 2CH TSOT-23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率(每秒):15 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:1 功率耗散(最大):480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN(5x7) 包裝:帶卷 (TR) 輸入數目和類型:16 個單端,雙極;8 個差分,雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7912AUJZ-REEL7 功能描述:IC ADC 10BIT DUAL 2CH TSOT-23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7914 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP
AD7914BRU 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 10-bit Serial 16-Pin TSSOP 制造商:Analog Devices 功能描述:IC 10BIT ADC SMD 7914 TSSOP16
AD7914BRU-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 10-bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 1MSPS 10-BIT SERL 16TSSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:10-BIT 4,CH 1 MSPS ADC I.C. - Tape and Reel
主站蜘蛛池模板: 金乡县| 富平县| 泸西县| 聂拉木县| 金山区| 东平县| 颍上县| 海晏县| 大方县| 衡山县| 托克逊县| 伊通| 辽阳市| 额尔古纳市| 灵宝市| 涞源县| 阿坝县| 家居| 义乌市| 广南县| 特克斯县| 原阳县| 津市市| 桃江县| 沁阳市| 始兴县| 松溪县| 连州市| 万安县| 滁州市| 林口县| 伽师县| 铜川市| 凌云县| 锦州市| 湾仔区| 巴东县| 武邑县| 四会市| 屯留县| 灌阳县|