- 您現在的位置：買賣IC網 > PDF目錄373925 > AD7918BRU-REEL (ANALOG DEVICES INC) 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP PDF資料下載
參數資料
| 型號： | AD7918BRU-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP |
| 中文描述： | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| 封裝： | MO-153AC, TSSOP-20 |
| 文件頁數： | 14/24頁 |
| 文件大?。?/td> | 607K |
| 代理商： | AD7918BRU-REEL |
AD7908/AD7918/AD7928
REV. A
Table II. Channel Selection
ADD2
ADD1
ADD0
Analog Input Channel
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
V
IN
0
V
IN
1
V
IN
2
V
IN
3
V
IN
4
V
IN
5
V
IN
6
V
IN
7
Table III. Power Mode Selection
PM1 PM0 Mode
1
1
Normal Operation
. In this mode, the AD7908/
AD7918/AD7928 remain in full power mode
regardless of the status of any of the logic inputs.
This mode allows the fastest possible throughput
rate from the AD7908/AD7918/AD7928.
Full Shutdown
. In this mode, the AD7908/
AD7918/AD7928 is in full shutdown mode with
all circuitry powering down. The AD7908/AD7918/
AD7928 retains the information in the Control
Register while in full shutdown. The part remains in
full shutdown until these bits are changed.
Auto Shutdown
. In this mode, the AD7908/
AD7918/AD7928 automatically enters full
shutdown mode at the end of each conversion
when the control register is updated. Wake-up
time from full shutdown is 1 μs and the user
should ensure that 1 μs has elapsed before
attempting to perform a valid conversion on the
part in this mode.
Invalid Selection
. This configuration is not allowed.
1
0
0
1
0
0
SEQUENCER OPERATION
The configuration of the SEQ and SHADOW bits in the
Control Register allows the user to select a particular mode of
operation of the sequencer function. Table IV outlines the four
modes of operation of the Sequencer.
Table IV. Sequence Selection
SEQ SHADOW
Sequence Type
0
0
This configuration means that the sequence
function is not used. The analog input
channel selected for each individual
conversion is determined by the contents of
the channel address bits ADD0 through
ADD2 in each prior write operation. This
mode of operation reflects the traditional
operation of a multichannel ADC, without
the Sequencer function being used, where
each write to the AD7908/AD7918/
AD7928 selects the next channel for
conversion. (See Figure 2.)
This configuration selects the SHADOW
Register for programming. The following
write operation will load the contents of the
SHADOW Register. This will program the
sequence of channels to be converted on
continuously with each successive valid
CS
falling edge. (See SHADOW Register
section, Table V, and Figure 3.) The
channels selected need not be consecutive.
If the SEQ and SHADOW bits are set in
this way, then the sequence function will
not be interrupted upon completion of the
WRITE operation. This allows other bits in
the Control Register to be altered between
conversions while in a sequence, without
terminating the cycle.
This configuration is used in conjunction
with the channel address bits ADD2 to
ADD0 to program continuous conversions
on a consecutive sequence of channels from
Channel 0 to a selected final channel as
determined by the channel address bits in
the Control Register. (See Figure 4.)
0
1
1
0
1
1
–14–
相關PDF資料 |
PDF描述 |
|---|---|
| AD7918BRU-REEL7 | 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP |
| AD7928 | 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP |
| AD7928BRU | 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP |
| AD7928BRU-REEL | 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP |
| AD7928BRU-REEL7 | 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7918BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 10-bit Serial 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 1MSPS 10-BIT SERL 20TSSOP - Tape and Reel |
| AD7918BRUZ | 功能描述:IC ADC 10BIT 8CH 1MSPS 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7918BRUZ-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs |
| AD7918BRUZ-REEL7 | 功能描述:IC ADC 10BIT 8CH W/SEQ 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7918WYRUZ-REEL7 | 功能描述:IC ADC 10BIT 8CH W/SEQ 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。