- 您現在的位置：買賣IC網 > PDF目錄373926 > AD7920AKS-500RL7 (ANALOG DEVICES INC) 250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 PDF資料下載
參數資料
| 型號： | AD7920AKS-500RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
| 中文描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO6 |
| 封裝： | MO-203AB, SC-70, 6 PIN |
| 文件頁數： | 11/20頁 |
| 文件大小： | 1091K |
| 代理商： | AD7920AKS-500RL7 |
REV. B
AD7910/AD7920
–11–
When the ADC starts a conversion (see Figure 5), SW2 opens
and SW1 moves to position B, causing the comparator to become
unbalanced. The control logic and charge redistribution DAC are
used to add and subtract fixed amounts of charge from the
sampling capacitor to bring the comparator back into a balanced
condition. When the comparator is rebalanced, the conversion
is complete. The control logic generates the ADC output code.
Figure 6 shows the ADC transfer function.
CHARGE
REDISTRIBUTION
DAC
CONTROL
LOGIC
COMPARATOR
SW2
SAMPLING
CAPACITOR
CONVERSION
PHASE
SW1
A
B
AGND
V
DD
/2
V
IN
Figure 5. ADC Conversion Phase
ADC Transfer Function
The output coding of the AD7910/AD7920 is straight binary.
The designed code transitions occur at the successive integer
LSB values, i.e., 1 LSB, 2 LSBs, and so on. The LSB size is
V
DD
/4096 for the AD7920 and V
DD
/1024 for the AD7910. The
ideal transfer characteristic for the AD7910/AD7920 is shown
in Figure 6.
000...000
0V
A
ANALOG INPUT
111...111
111...110
000...001
000...010
111...000
011...111
1LSB
+V
DD
–1LSB
1LSB = V
DD
/1024 (AD7910)
1LSB = V
DD
/4096 (AD7920)
Figure 6. Transfer Characteristic
Typical Connection Diagram
Figure 7 shows a typical connection diagram for the AD7910/
AD7920. V
REF
is taken internally from V
DD
and, as such, V
DD
should be well decoupled. This provides an analog input range of
0 V to V
DD
. The conversion result is output in a 16-bit word with
four leading zeros followed by the MSB of the 12-bit or 10-bit
result. The 10-bit result from the AD7910 will be followed by two
trailing zeros.
Alternatively, because the supply current required by the AD7910/
AD7920 is so low, a precision reference can be used as the
supply source to the AD7910/AD7920. An REF19x voltage
reference (REF195 for 5 V or REF193 for 3 V) can be used to
supply the required voltage to the ADC (see Figure 7). This con-
figuration is especially useful if the power supply is quite noisy
or if the system supply voltages are at a value other than 5 V or
3 V (e.g., 15 V). The REF19x will output a steady voltage to the
AD7910/AD7920. If the low dropout REF193 is used, the current
it needs to supply to the AD7910/AD7920 is typically 1.2 mA.
When the ADC is converting at a rate of 250 kSPS the REF193
needs to supply a maximum of 1.4 mA to the AD7910/AD7920.
The load regulation of the REF193 is typically 10 ppm/mA
(REF193, V
S
= 5 V), which results in an error of 14 ppm (42
m
V)
for the 1.4 mA
drawn from it. This corresponds to a 0.057 LSB
error for the AD7920 with V
DD
= 3 V from the REF193 and a
0.014 LSB error for the AD7910. For applications where power
consumption is of concern, the power-down mode of the ADC
and the sleep mode of the REF19x reference should be used to
improve power performance. See the Modes of Operation section.
AD7910/
AD7920/
SCLK
SDATA
CS
V
IN
GND
0V TO V
INPUT
V
DD
C/ P
SERIAL
INTERFACE
0.1 F
1 F
TANT
REF193
1.2mA
680nF
10 F
0.1 F
3V
5V
SUPPLY
Figure 7. REF193 as Power Supply
Table I provides typical performance data with various references
used as a V
DD
source for a 100 kHz input tone at room temper-
ature under the same setup conditions.
Table I. AD7920 Typical Performance
for Various Voltage References IC
Reference
Tied to V
DD
AD780 @ 3 V
REF193
AD780 @ 2.5 V
REF192
REF43
AD7920 SNR
Performance (dB)
72.65
72.35
72.5
72.2
72.6
相關PDF資料 |
PDF描述 |
|---|---|
| AD7920BKS | 250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
| AD7920BKS-REEL | 250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
| AD7920BRM-REEL | 250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
| AD7920BRM-REEL7 | 250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
| AD7911ARM | 2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7920AKS-REEL | 制造商:Analog Devices 功能描述: |
| AD7920AKS-REEL7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7920AKSZ-500RL7 | 功能描述:IC ADC 12BIT SRL 250KSPS SC70-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7920AKSZ-REEL7 | 功能描述:IC ADC 12BIT SRL 250KSPS SC70-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7920BKS | 制造商:AD 制造商全稱:Analog Devices 功能描述:250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
發布緊急采購，3分鐘左右您將得到回復。