- 您現在的位置：買賣IC網 > PDF目錄373927 > AD7997 (Analog Devices, Inc.) 8-Channel, 10- and 12-Bit ADCs with I2CCompatible PDF資料下載
參數資料
| 型號： | AD7997 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 串行ADC |
| 英文描述： | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| 中文描述： | 8通道，10 -和12位ADC與I2CCompatible |
| 文件頁數： | 23/32頁 |
| 文件大小： | 1056K |
| 代理商： | AD7997 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7997/AD7998
SERIAL INTERFACE
Control of the AD7997/AD7998 is carried out via the I
2
C-
compatible serial bus. The devices are connected to this bus as
slave devices under the control of a master device, such as the
processor.
Rev. 0 | Page 23 of 32
SERIAL BUS ADDRESS
Like all I
2
C-compatible devices, the AD7997/AD7998 have a
7-bit serial address. The 3 MSBs of this address for the AD7997/
AD7998 are set to 010. The AD7997/AD7998 come in two
versions, the AD7997-0/AD7997-0 and AD7997-1AD7998-1.
The two versions have three different I
2
C addresses available,
which are selected by either tying the address select pin, AS, to
AGND or V
DD
, or by letting the pin float (see Table 6). By giving
different addresses for the two versions, up to five AD7997/
AD7998 devices can be connected to a single serial bus, or the
addresses can be set to avoid conflicts with other devices on the
bus. (See Table 6.)
The serial bus protocol operates as follows.
The master initiates data transfer by establishing a start
condition, defined as a high-to-low transition on the serial
data line SDA, while the serial clock line, SCL, remains high.
This indicates that an address/data stream follows. All slave
peripherals connected to the serial bus responds to the start
condition and shift in the next eight bits, consisting of a
7-bit address (MSB first) plus an R/W bit that determines the
direction of the data transfer, that is, whether data is written to
or read from the slave device.
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the low
period before the ninth clock pulse, known as the acknowledge
bit. All other devices on the bus remain idle while the selected
device waits for data to be read from or written to it. If the R/W
bit is a 0, the master writes to the slave device. If the R/W bit is a
1, the master reads from the slave device.
Data is sent over the serial bus in sequences of nine clock
pulses, eight bits of data followed by an acknowledge bit from
the receiver of data. Transitions on the data line must occur
during the low period of the clock signal and remain stable
during the high period because a low-to-high transition when
the clock is high may be interpreted as a stop signal.
When all data bytes have been read or written, stop conditions
are established. In write mode, the master pulls the data line
high during the 10th clock pulse to assert a stop condition. In
read mode, the master device pulls the data line high during the
low period before the ninth clock pulse. This is known as No
Acknowledge. The master then takes the data line low during
the low period before the 10th clock pulse, then high during the
10th clock pulse to assert a stop condition.
Any number of bytes of data may be transferred over the serial
bus in one operation, but it is not possible to mix read and write
in one operation, because the type of operation is determined at
the beginning and cannot subsequently be changed without
starting a new operation.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7997BRU-0 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRU-0REEL | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRU-1 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRU-1REEL | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
| AD7997BRUZ-03 | 8-Channel, 10- and 12-Bit ADCs with I2CCompatible |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7997BRU-0 | 功能描述:IC ADC 10BIT 8CHAN I2C 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7997BRU-0REEL | 功能描述:IC ADC 10BIT 8CHAN I2C 20TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7997BRU-1 | 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 10-bit Serial 20-Pin TSSOP 制造商:Rochester Electronics LLC 功能描述:8-CHANNEL, 10-BIT ADC WITH 12C ITF I.C. - Bulk |
| AD7997BRU-1REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 188ksps 10-bit Serial 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 188KSPS 10-BIT SERL 20SSOP - Tape and Reel |
| AD7997BRU-O | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。