- 您現在的位置：買賣IC網 > PDF目錄373932 > AD8045ACPZ-REEL (ANALOG DEVICES INC) 3 nV/Hz Ultralow Distortion, High Speed Op Amp PDF資料下載
參數資料
| 型號： | AD8045ACPZ-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 3 nV/Hz Ultralow Distortion, High Speed Op Amp |
| 中文描述： | OP-AMP, 1000 uV OFFSET-MAX, DSO8 |
| 封裝： | 3 X 3 MM, LEAD FREE, CSP-8 |
| 文件頁數： | 23/24頁 |
| 文件大小： | 474K |
| 代理商： | AD8045ACPZ-REEL |
AD8045
EXPOSED PADDLE
The AD8045 features an exposed paddle, which lowers the
thermal resistance by 25% compared to a standard SOIC plastic
package. The exposed paddle of the AD8045 is internally con-
nected to the negative power supply pin. Therefore, when laying
out the board, the exposed paddle must either be connected to
the negative power supply or left floating (electrically isolated).
Soldering the exposed paddle to the negative power supply metal
ensures maximum thermal transfer. Figure 74 and Figure 75 show
the proper layout for connecting the SOIC and LFCSP exposed
paddle to the negative supply.
Rev. A | Page 23 of 24
0
Figure 74. SOIC Exposed Paddle Layout
The use of thermal vias or “heat pipes” can also be incorporated
into the design of the mounting pad for the exposed paddle.
These additional vias help to lower the overall theta junction to
ambient (θ
JA
). Using a heavier weight copper on the surface to
which the amplifier’s exposed paddle is soldered can greatly
reduce the overall thermal resistance “seen” by the AD8045.
0
Figure 75. LFCSP Exposed Paddle Layout
For existing designs that want to incorporate the AD8045,
electrically isolating the exposed paddle is another option. If the
exposed paddle is electrically isolated, the thermal dissipation is
primarily through the leads, and the thermal resistance of the
package now approaches 125°C/W, the standard SOIC θ
JA
.
However, a thermally conductive and electrically isolated pad
material may be used. A thermally conductive spacer, such as
the Bergquist Company’s Sil-Pad, is an excellent solution to this
problem. Figure 76 shows a typical implementation using
thermal pad material.
0
THERMAL CONDUCTIVE INSULATOR
Figure 76. SOIC with Thermal Conductive Pad Material
The thermal pad provides high thermal conductivity but
isolates the exposed paddle from ground or other potential. It is
recommended, when possible, to solder the paddle to the nega-
tive power supply plane or trace for maximum thermal transfer.
Note that soldering the paddle to ground shorts the negative
power supply to ground and can cause irreparable damage to
the AD8045.
DRIVING CAPACITIVE LOADS
In general, high speed amplifiers have a difficult time driving
capacitive loads. This is particularly true in low closed-loop
gains, where the phase margin is the lowest. The difficulty arises
because the load capacitance, C
L
, forms a pole with the output
resistance, R
O
, of the amplifier. The pole can be described by the
equation
L
O
P
C
R
f
2π
1
=
If this pole occurs too close to the unity gain crossover point,
the phase margin degrades. This is due to the additional phase
loss associated with the pole.
The AD8045 output can drive 18 pF of load capacitance directly,
in a gain of +2 with 30% overshoot, as shown in Figure 37.
Larger capacitance values can be driven but must use a snub-
bing resistor (R
SNUB
) at the output of the amplifier, as shown in
Figure 61 and Figure 62. Adding a small series resistor, R
SNUB
,
creates a zero that cancels the pole introduced by the load
capacitance. Typical values for R
SNUB
can range from 25 to
50 . The value is typically arrived at empirically and based on
the circuit requirements.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8045ACPZ-REEL7 | 3 nV/Hz Ultralow Distortion, High Speed Op Amp |
| AD8045ARD | 3 nV/Hz Ultralow Distortion, High Speed Op Amp |
| AD8045ARD-REEL | 3 nV/Hz Ultralow Distortion, High Speed Op Amp |
| AD8045ARD-REEL7 | 3 nV/Hz Ultralow Distortion, High Speed Op Amp |
| AD8045ARDZ | 3 nV/Hz Ultralow Distortion, High Speed Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8045ACPZ-REEL7 | 功能描述:IC OPAMP VF ULDIST LN 8LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD8045AR | 制造商:Analog Devices 功能描述:ULTRA-LOW DISTORTION HIGH SPEED AMPLIFIER - Bulk |
| AD8045ARD | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk 制造商:Analog Devices 功能描述:IC OP-AMP HIGH SPEED |
| AD8045ARD-EBZ | 功能描述:BOARD EVAL FOR AD8045ARD RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8045ARD-REEL | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk 制造商:Analog Devices 功能描述:OP AMP SGL VOLT FDBK 6V/12V 8SOIC N EP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。