- 您現在的位置：買賣IC網 > PDF目錄373934 > AD8063ART-R2 (ANALOG DEVICES INC) Low Cost, 300 MHz Rail-to-Rail Amplifiers PDF資料下載
參數資料
| 型號： | AD8063ART-R2 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Low Cost, 300 MHz Rail-to-Rail Amplifiers |
| 中文描述： | OP-AMP, 6000 uV OFFSET-MAX, PDSO6 |
| 封裝： | MO-178AB, SOT-23, 6 PIN |
| 文件頁數： | 17/20頁 |
| 文件大小： | 302K |
| 代理商： | AD8063ART-R2 |
AD8061/AD8062/AD8063
APPLICATIONS
SINGLE-SUPPLY SYNC STRIPPER
When a video signal contains synchronization pulses, it is
sometimes desirable to remove them prior to performing
certain operations. In the case of A-to-D conversion, the sync
pulses consume some of the dynamic range, so removing them
increases the converter’s available dynamic range for the video
information.
Rev. D | Page 17 of 20
Figure 53 shows a basic circuit for creating a sync stripper using
the AD8061 powered by a single supply. When the negative
supply is at ground potential, the lowest potential to which the
output can go is ground. This feature is exploited to create a
waveform whose lowest amplitude is the black level of the video
and does not include the sync level.
75
Ω
VIDEO OUT
75
Ω
R
G
1k
Ω
75
Ω
R
F
1k
Ω
10
μ
F
3V
AD8061
0.1
μ
F
3
2
4
6
7
VIDEO IN
PIN NUMBERS ARE
FOR 8-LEAD PACKAGE
0
Figure 53. Single 3 V Sync Stripper Using AD8061
In this case, the input video signal has its black level at ground, so
it comes out at ground at the input. Since the sync level is below
the black level, it will not show up at the output. However, all of
the active video portion of the waveform will be amplified by a
gain of two and then be normalized to unity gain by the back-
terminated transmission line. Figure 54 is an oscilloscope plot
of the input and output waveforms.
0
500mV
INPUT
OUTPUT
1
2
10
μ
s
Figure 54. Input and Output Waveforms for a Single-Supply
Video Sync Stripper Using an AD8061
Some video signals with sync are derived from single-supply
devices, such as video DACs. These signals can contain sync,
but the whole waveform is positive, and the black level is not
at ground but at some positive voltage.
The circuit can be modified to provide the sync stripping
function for such a waveform. Instead of connecting R
G
to
ground, connect it to a dc voltage that is two times the black
level of the input signal. The gain from the +input to the output
is two, which means the black level will be amplified by two to
the output. However, the gain through R
G
is –unity to the
output. It takes a dc level of twice the input black level to shift
the black level to ground at the output. When this occurs, the
sync will be stripped, and the active video will be passed as in
the ground-referenced case.
75
Ω
10
μ
F
0.1
μ
F
3V
3
2
4
6
7
75
Ω
MONITOR
#1
75
Ω
75
Ω
75
Ω
1k
Ω
1k
Ω
1k
Ω
1k
Ω
3V
1k
Ω
3
2
5
6
7
8
1
4
MONITOR
#2
DAC
RED
GREEN
BLUE
RED
DAC
DAC
75
Ω
75
Ω
75
Ω
75
Ω
AD8061
75
Ω
10
μ
F
0.1
μ
F
1k
Ω
AD8062
75
Ω
AD8062
75
Ω
0
Figure 55. RGB Cable Driver Using AD8061 and AD8062
RGB AMPLIFIER
Most RGB graphics signals are created by video DAC outputs
that drive a current through a resistor to ground. At the video
black level, the current goes to zero, and the voltage of the video
is also zero. Before the availability of high speed rail-to rail op
amps, it was essential that an amplifier have a negative supply
to amplify such a signal. Such an amplifier is necessary if one
wants to drive a second monitor from the same DAC outputs.
However, high speed, rail-to-rail output amplifiers like the
AD8061 and AD8062 accept ground level input signals and
output ground level signals. They are used as RGB signal
amplifiers. A combination of the AD8061 (single) and the
AD8062 (dual) amplifies the three video channels of an RGB
system. Figure 55 shows a circuit that performs this function.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8063ARTZ-R2 | Low Cost, 300 MHz Rail-to-Rail Amplifiers |
| AD8063ARTZ-REEL | Low Cost, 300 MHz Rail-to-Rail Amplifiers |
| AD8063ARTZ-REEL7 | Low Cost, 300 MHz Rail-to-Rail Amplifiers |
| AD8063ARZ | Low Cost, 300 MHz Rail-to-Rail Amplifiers |
| AD8063ARZ-REEL | Low Cost, 300 MHz Rail-to-Rail Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8063ART-REEL | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 6-Pin SOT-23 T/R |
| AD8063ART-REEL7 | 功能描述:IC OPAMP VF R-R LP 50MA SOT23-6 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 |
| AD8063ARTZ | 制造商:Analog Devices 功能描述:OP AMP 300MHZ 650V/US 6SOT2 制造商:Analog Devices 功能描述:OP AMP, 300MHZ, 650V/US, 6SOT23; Op Amp Type:Voltage Feedback; No. of Amplifiers:1; Slew Rate:650V/s; Supply Voltage Range:2.7V to 8V; Amplifier Case Style:SOT-23; No. of Pins:6; Bandwidth:320MHz; Operating Temperature Min:-40C; ;RoHS Compliant: Yes |
| AD8063ARTZR2 | 制造商:Analog Devices 功能描述:AD8063 rail-to-rail 300 MHz SOT23 op amp |
| AD8063ARTZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 8V 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:OP AMP SGL VOLT FDBK R-R O/P 8V 6PIN SOT-23 - Tape and Reel 制造商:Analog Devices 功能描述:Op Amp 300MHz RRO with Disable SOT23-6 |
發布緊急采購，3分鐘左右您將得到回復。