- 您現在的位置：買賣IC網 > PDF目錄373937 > AD8130 (ANALOG DEVICES INC) Low-Cost 270 MHz Differential Receiver Amplifiers PDF資料下載
參數資料
| 型號： | AD8130 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Low-Cost 270 MHz Differential Receiver Amplifiers |
| 中文描述： | LINE RECEIVER |
| 文件頁數： | 25/28頁 |
| 文件大小： | 510K |
| 代理商： | AD8130 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁
REV. 0
AD8129/AD8130
–25–
Power Dissipation
The AD8129/AD8130 can operate with supply voltages from
+5 V to
±
12 V. The major reason for such a wide supply range
is to provide a wide input common-mode range for systems
that might require this. This would be encountered when sig-
nificant common-mode noise couples into the input path. For
applications that do not require a wide input or output dynamic
range, it is recommended to operate with lower supply voltages.
The AD8129/AD8130 is also available in a very small Micro_SO-8
package. This has higher thermal impedance than larger packages
and will operate at a higher temperature with the same amount
of power dissipation. Certain operating conditions that are within
the specification range of the parts can cause excess power dissi-
pation. Caution should be exercised.
The power dissipation is a function of several operating condi-
tions. These include the supply voltage, the input differential
voltage, the output load and the signal frequency.
A basic starting point is to calculate the quiescent power dissipa-
tion with no signal and no differential input voltage. This is just
the product of the total supply voltage and the quiescent operat-
ing current. The maximum operating supply voltage is 26.4 V
and the quiescent current is 13 mA. This causes a quiescent
power dissipation of 343 mW. For the Micro_SO package, the
θ
JA
specification is 142
°
C/W. So the quiescent power will cause
about a 49
°
C rise above ambient in the Micro_SO package.
The current consumption is also a function of the differential
input voltage. (See TPCs 109 and 110.) This current should be
added on to the quiescent current and then multiplied by the
total supply voltage to calculate the power.
The AD8129/AD8130 can directly drive loads of as low as
100
, such as a terminated 50
cable. The worst-case power
dissipation in the output stage occurs when the output is at
midsupply. As an example, for a 12 V supply and the output
driving a 250
load to ground, the maximum power dissipation
in the output will occur when the output voltage is 6 V.
The load current will be 6 V/250
= 24 mA. This same current
will flow through the output across a 6 V drop from +V
S
. This
will dissipate 144 mW. For the Micro_SO-8 package, this causes a
temperature rise of 20
°
C above ambient. Although this is a worst-
case number, it is apparent that this can be a considerable
additional amount of power dissipation.
Several changes can be made to alleviate this. One is to use the
standard SO-8 package. This will lower the thermal impedance
to 121
°
C/W, which is a 15% improvement. Next is to use a
lower supply voltage unless absolutely necessary.
Finally, do not use the AD8129/AD8130 to directly drive a
heavy load when it is operating on high supply voltages. It is
best to use a second op amp after the output stage. Some of the
gain can be shifted to this stage so that the signal swing at the
output of the AD8129/AD8130 is not too large.
Layout, Grounding and Bypassing
The AD8129/AD8130 are very high-speed parts that can be
sensitive to the PCB environment in which they have to oper-
ate. Realizing their superior specifications requires attention
to various details of standard high-speed PCB design practice.
The first requirement is for a good solid ground plane that cov-
ers as much of the board area around the AD8129/AD8130 as
possible. The only exception to this is that the ground plane
around the FB pin should be kept a few mm away, and ground
should be removed from inner layers and the opposite side of
the board under this pin. This will minimize the stray capaci-
tance on this node and help preserve the gain flatness versus
frequency.
The power supply pins should be bypassed as close as possible
to the device to the nearby ground plane. Good high-frequency
ceramic chip capacitors should be used. This bypassing should
be done with a capacitance value of 0.01
μ
F to 0.1
μ
F for each
supply. Further away, low frequency bypassing should be provided
with 10
μ
F tantalum capacitors from each supply to ground.
The signal routing should be short and direct in order to avoid
parasitic effects. Where possible, signals should be run over
ground planes to avoid radiating, or to avoid being susceptible
to other radiation sources.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8130-EVAL | Low-Cost 270 MHz Differential Receiver Amplifiers |
| AD8130AR | Low-Cost 270 MHz Differential Receiver Amplifiers |
| AD8130AR-REEL1 | Low-Cost 270 MHz Differential Receiver Amplifiers |
| AD8130AR-REEL72 | Low-Cost 270 MHz Differential Receiver Amplifiers |
| AD8130ARM | Low-Cost 270 MHz Differential Receiver Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8130AR | 功能描述:IC AMP DIFF LN LDIST 40MA 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD8130AR | 制造商:Analog Devices 功能描述:SEMICONDUCTOR ((NW)) |
| AD8130AR-EB | 制造商:Analog Devices 功能描述:LEADED EVALUATION BOARD - Boxed Product (Development Kits) |
| AD8130AR-EBZ | 功能描述:BOARD EVAL FOR AD8130AR RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8130ARM | 功能描述:IC AMP DIFF LN LDIST 40MA 8MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。