欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD8130ARZ-REEL7
廠商: ANALOG DEVICES INC
元件分類: 模擬信號調理
英文描述: Low Cost 270 MHz Differential Receiver Amplifiers
中文描述: SPECIALTY ANALOG CIRCUIT, PDSO8
封裝: LEAD FREE, SOIC-8
文件頁數: 37/40頁
文件大小: 549K
代理商: AD8130ARZ-REEL7
AD8129/AD8130
Another problem can occur with the AD8129 operating
at a supply voltage of greater than or equal to ±12 V. The
architecture causes the supply current to increase as the input
differential voltage increases. If the AD8129 differential inputs
are overdriven too far, excessive current can flow into the device
and potentially cause permanent damage.
Rev. C | Page 37 of 40
A practical means to prevent this from occurring is to clamp the
inputs differentially with a pair of antiparallel Schottky diodes
(see Figure 146). These diodes have a lower forward voltage of
approximately 0.4 V. If the differential voltage across the inputs
is restricted to these conditions, no excess current is drawn by
the AD8129 under these operating conditions.
If the supply voltage is restricted to less than ±11 V, the internal
clamping circuit limits the differential voltage and excessive
supply current is not drawn. The external clamp circuit is not
needed.
V
IN
AGILENT
HSMS 2822
1
2
3
V
OUT
–V
+V
–V
S
2
PD
+V
S
+
+
V
IN
AD8129
6
5
4
8
1
3
7
0.1
μ
F
10
μ
F
0.1
μ
F
10
μ
F
0
Figure 146. Schottky Diodes Across the Inputs
Limits the Input Differential Voltage
In both circuits, the input series resistors function to limit the
current through the diodes when they are forward biased. As a
practical matter, these resistors must be matched so that the
CMRR is preserved at high frequencies. These resistors have
minimal effect on the CMRR at low frequency.
POWER DISSIPATION
The AD8129/AD8130 can operate with supply voltages from
+5 V to ±12 V. The major reason for such a wide supply range is
to provide a wide input common-mode range for systems that
can require this. This would be encountered when significant
common-mode noise couples into the input path. For applications
that do not require a wide dynamic range for the input or output, it
is recommended to operate with lower supply voltages.
The AD8129/AD8130 is also available in a very small 8-lead
MSOP package. This package has higher thermal impedance
than larger packages and operates at a higher temperature with
the same amount of power dissipation. Certain operating
conditions that are within the specifications range of the parts can
cause excess power dissipation. Caution should be exercised.
The power dissipation is a function of several operating
conditions, including the supply voltage, the input differential
voltage, the output load, and the signal frequency.
A basic starting point is to calculate the quiescent power
dissipation with no signal and no differential input voltage.
This is just the product of the total supply voltage and the
quiescent operating current. The maximum operating supply
voltage is 26.4 V, and the quiescent current is 13 mA. This
causes a quiescent power dissipation of 343 mW. For the
MSOP package, the θ
JA
specification is 142°C/W. Therefore,
the quiescent power causes about a 49°C rise above ambient
in the MSOP package.
The current consumption is also a function of the differential
input voltage (see Figure 113 and Figure 114). This current
should be added onto the quiescent current and then multiplied
by the total supply voltage to calculate the power.
The AD8129/AD8130 can directly drive loads of as low as
100 Ω, such as a terminated 50 Ω cable. The worst-case power
dissipation in the output stage occurs when the output is at
midsupply. As an example, for a 12 V supply with the output
driving a 250 Ω load to ground, the maximum power dissipation
in the output occurs when the output voltage is 6 V. The load
current is 6 V/250 Ω = 24 mA. This same current flows through
the output across a 6 V drop from V
S
. It dissipates 144 mW. For
the 8-lead MSOP package, this causes a temperature rise of
20°C above ambient. Although this is a worst-case number, it is
apparent that this can be a considerable additional amount of
power dissipation.
Several changes can be made to alleviate this. One is to use the
standard 8-lead SOIC package. This lowers the thermal impedance
to 121°C/W, which is a 15% improvement. Another is to use a
lower supply voltage unless absolutely necessary.
Finally, do not use the AD8129/AD8130 when it is operating on
high supply voltages to directly drive a heavy load. It is best to
use a second op amp after the output stage. Some of the gain
can be shifted to this stage so that the signal swing at the output
of the AD8129/AD8130 is not too large.
相關PDF資料
PDF描述
AD8129ARM-REEL Low Cost 270 MHz Differential Receiver Amplifiers
AD8129ARM-REEL7 Low Cost 270 MHz Differential Receiver Amplifiers
AD8129ARMZ Low Cost 270 MHz Differential Receiver Amplifiers
AD8129ARMZ-REEL Low Cost 270 MHz Differential Receiver Amplifiers
AD8129ARMZ-REEL7 Low Cost 270 MHz Differential Receiver Amplifiers
相關代理商/技術參數
參數描述
AD8130-EVAL 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost 270 MHz Differential Receiver Amplifiers
AD8131 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost, High-Speed Differential Driver
AD8131_05 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, High Speed Differential Driver
AD8131AR 功能描述:IC AMP DIFF LDIST 60MA 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源,單路/雙路(±):2 V ~ 44 V,±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP(5x3) 包裝:管件
AD8131AR-EBZ 功能描述:BOARD EVAL FOR AD8131AR RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
主站蜘蛛池模板: 万荣县| 明溪县| 拉萨市| 交城县| 新和县| 焉耆| 娄烦县| 肥西县| 静宁县| 高陵县| 雅江县| 孙吴县| 遂宁市| 丰顺县| 海城市| 灌阳县| 肃宁县| 瑞金市| 古浪县| 吕梁市| 阳新县| 凤庆县| 繁峙县| 和平区| 三门峡市| 罗江县| 文山县| 牟定县| 措勤县| 青神县| 曲麻莱县| 金华市| 南城县| 阳信县| 建平县| 寿阳县| 华蓥市| 虹口区| 贵南县| 牟定县| 曲周县|