- 您現在的位置：買賣IC網 > PDF目錄373938 > AD8138ARMZ-REEL7 (ANALOG DEVICES INC) Low Distortion Differential ADC Driver PDF資料下載
參數資料
| 型號： | AD8138ARMZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Low Distortion Differential ADC Driver |
| 中文描述： | LINE DRIVER, PDSO8 |
| 封裝： | LEAD FREE, MO-187AA, MSOP-8 |
| 文件頁數： | 19/24頁 |
| 文件大小： | 318K |
| 代理商： | AD8138ARMZ-REEL7 |
AD8138
LAYOUT, GROUNDING, AND BYPASSING
As a high speed part, the AD8138 is sensitive to the PCB
environment in which it has to operate. Realizing its superior
specifications requires attention to various details of good high
speed PCB design.
Rev. F | Page 19 of 24
The first requirement is for a good solid ground plane that
covers as much of the board area around the AD8138 as
possible. The only exception to this is that the two input pins
(Pin 1 and Pin 8) should be kept a few millimeters from the
ground plane, and ground should be removed from inner layers
and the opposite side of the board under the input pins. This
minimizes the stray capacitance on these nodes and helps
preserve the gain flatness vs. frequency.
The power supply pins should be bypassed as close as possible
to the device to the nearby ground plane. Good high frequency
ceramic chip capacitors should be used. This bypassing should
be done with a capacitance value of 0.01 μF to 0.1 μF for each
supply. Further away, low frequency bypassing should be provided
with 10 μF tantalum capacitors from each supply to ground.
The signal routing should be short and direct to avoid parasitic
effects. Wherever there are complementary signals, a symmetrical
layout should be provided to the extent possible to maximize
the balance performance. When running differential signals
over a long distance, the traces on the PCB should be close
together or any differential wiring should be twisted together to
minimize the area of the loop that is formed. This reduces the
radiated energy and makes the circuit less susceptible to
interference.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8138ARZ | Low Distortion Differential ADC Driver |
| AD8138ARZ-R7 | Low Distortion Differential ADC Driver |
| AD8138ARZ-RL | Low Distortion Differential ADC Driver |
| AD8138 | Low Distortion Differential I/O Amplifier(小失真差分輸入/輸出放大器) |
| AD8139ARDZ-REEL | Low Noise Rail-to-Rail Differential ADC Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8138AR-REEL | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8138AR-REEL7 | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8138ARZ | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8138ARZ-R7 | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8138ARZ-RL | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。