- 您現在的位置：買賣IC網 > PDF目錄373938 > AD8139ARDZ1 (Analog Devices, Inc.) Low Noise Rail-to-Rail Differential ADC Driver PDF資料下載
參數資料
| 型號： | AD8139ARDZ1 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Noise Rail-to-Rail Differential ADC Driver |
| 中文描述： | 低噪聲軌至軌差分ADC驅動器 |
| 文件頁數： | 22/24頁 |
| 文件大小： | 720K |
| 代理商： | AD8139ARDZ1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁
AD8139
Driving a Capacitive Load
A purely capacitive load will react with the bondwire and pin
inductance of the AD8139, resulting in high frequency ringing
in the transient response and loss of phase margin. One way to
minimize this effect is to place a small resistor in series with
each output to buffer the load capacitance, see Figure 6 and
Figure 61. The resistor and load capacitance will form a first-
order low-pass filter; therefore, the resistor value should be as
small as possible. In some cases, the ADCs require small series
resistors to be added on their inputs.
Rev. A | Page 22 of 24
–13
–12
–11
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
0
1
2
3
4
10M
100M
1G
5
0
FREQUENCY (MHz)
C
R
S
= 30.1
C
L
= 15pF
R
S
= 60.4
C
L
= 15pF
R
S
= 60.4
C
L
= 5pF
R
S
= 0
C
L, dm
= 0pF
R
S
= 30.1
C
L
= 5pF
V
S
=
±
5V
V
= 0.1V p-p
G = 1 (R
= R
G
= 200
)
R
L, dm
= 1k
Figure 61. Frequency Response for
Various Capacitive Load and Series Resistance
The Typical Performance Characteristics that illustrate transient
response versus the capacitive load were generated using series
resistors in each output and a differential capacitive load.
Layout Considerations
Standard high speed PCB layout practices should be adhered to
when designing with the AD8139. A solid ground plane is recom-
mended and good wideband power supply decoupling networks
should be placed as close as possible to the supply pins.
To minimize stray capacitance at the summing nodes, the
copper in all layers under all traces and pads that connect to the
summing nodes should be removed. Small amounts of stray
summing-node capacitance will cause peaking in the frequency
response, and large amounts can cause instability. If some stray
summing-node capacitance is unavoidable, its effects can be
compensated for by placing small capacitors across the feedback
resistors.
Terminating a Single-Ended Input
Controlled impedance interconnections are used in most high
speed signal applications, and they require at least one line
termination. In analog applications, a matched resistive
termination is generally placed at the load end of the line. This
section deals with how to properly terminate a single-ended
input to the AD8139.
The input resistance presented by the AD8139 input circuitry is
seen in parallel with the termination resistor, and its loading
effect must be taken into account. The Thevenin equivalent
circuit of the driver, its source resistance, and the termination
resistance must all be included in the calculation as well. An
exact solution to the problem requires the solution of several
simultaneous algebraic equations and is beyond the scope of
this data sheet. An iterative solution is also possible and simpler,
especially considering the fact that standard 1% resistor values
are generally used.
Figure 62 shows the AD8139 in a unity-gain configuration
driving the AD6645, which is a 14-bit high speed ADC, and
with the following discussion, provides a good example of how
to provide a proper termination in a 50 environment.
The termination resistor, R
T
, in parallel with the 268 input
resistance of the AD8139 circuit (calculated using Equation 19),
yields an overall input resistance of 50 that is seen by the
signal source. In order to have matched feedback loops, each
loop must have the same R
G
if they have the same R
F
. In the
input (upper) loop, R
G
is equal to the 200 resistor in series
with the (+) input plus the parallel combination of R
T
and the
source resistance of 50 . In the upper loop, R
G
is therefore
equal to 228 . The closest standard 1% value to 228 Ω is 226
and is used for R
G
in the lower loop. Greater accuracy could be
achieved by using two resistors in series to obtain a resistance
closer to 228 .
Things get more complicated when it comes to determining the
feedback resistor values. The amplitude of the signal source
generator V
S
is two times the amplitude of its output signal
when terminated in 50 . Thus, a 2 V p-p terminated amplitude
is produced by a 4 V p-p amplitude from V
S
. The Thevenin
equivalent circuit of the signal source and R
T
must be used
when calculating the closed-loop gain because in the upper loop
R
G
is split between the 200 resistor and the Thevenin resis-
tance looking back toward the source. The Thevenin voltage of
the signal source is greater than the signal source output voltage
when terminated in 50 because R
T
must always be greater
than 50 . In this case, it is 61.9 and the Thevenin voltage
and resistance are 2.2 V p-p and 28 , respectively. Now the
upper input branch can be viewed as a 2.2 V p-p source in series
with 228 . Since this is a unity-gain application, a 2 V p-p
differential output is required, and R
F
must therefore be 228 ×
(2/2.2) = 206 . The closest standard value to this is 205 .
When generating the Typical Performance Characteristics data,
the measurements were calibrated to take the effects of the
terminations on closed-loop gain into account.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8139ARD-REEL7 | Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139ARD-REEL | Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139 | Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139ACPZ-R21 | PTSE 11C 11#16 STR PLUG |
| AD8139ACP-R2 | Low Noise Rail-to-Rail Differential ADC Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8139ARDZ-REEL | 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD8139ARDZ-REEL7 | 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD8139AR-REEL | 制造商:Analog Devices 功能描述:ULTRA LOW NOISE FULLY DIFFERENTIAL ADC DRIVER - Tape and Reel |
| AD8139CP | 制造商:Analog Devices 功能描述: |
| AD813ACHIPS | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Supply, Low Power Triple Video Amplifier |
發布緊急采購，3分鐘左右您將得到回復。