- 您現在的位置：買賣IC網 > PDF目錄373939 > AD815-EB (Analog Devices, Inc.) High Output Current Differential Driver PDF資料下載
參數資料
| 型號： | AD815-EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | High Output Current Differential Driver |
| 中文描述： | 高輸出電流差分驅動器 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 333K |
| 代理商： | AD815-EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁
AD815
REV. B
–12–
Other Power Considerations
There are additional power considerations applicable to the
AD815. First, as with many current feedback amplifiers, there is an
increase in supply current when delivering a large peak-to-peak
voltage to a resistive load at high frequencies. This behavior is
affected by the load present at the amplifier’s output. Figure 12
summarizes the full power response capabilities of the AD815.
These curves apply to the differential driver applications (e.g.,
Figure 49 or Figure 53). In Figure 12, maximum continuous
peak-to-peak output voltage is plotted vs. frequency for various
resistive loads. Exceeding this value on a continuous basis can
damage the AD815.
The AD815 is equipped with a thermal shutdown circuit. This
circuit ensures that the temperature of the AD815 die remains
below a safe level. In normal operation, the circuit shuts down
the AD815 at approximately 180
°
C and allows the circuit to
turn back on at approximately 140
°
C. This built-in hysteresis
means that a sustained thermal overload will cycle between
power-on and power-off conditions. The thermal cycling
typically occurs at a rate of 1ms to several seconds, depending
on the power dissipation and the thermal time constants of the
package and heat sinking. Figures 46 and 47 illustrate the
thermal shutdown operation after driving OUT1 to the + rail,
and OUT2 to the – rail, and then short-circuiting to ground
each output of the AD815. The AD815 will not be damaged by
momentary operation in this state, but the overload condition
should be removed.
10
0%
100
90
OUT 1
200
m
s
5V
OUT 2
Figure 46. OUT2 Shorted to Ground, Square Wave Is
OUT1, R
F
= 1 k
, R
G
= 222
10
0%
100
90
OUT 1
5ms
5V
OUT 2
Figure 47. OUT1 Shorted to Ground, Square Wave Is
OUT2, R
F
= 1 k
, R
G
= 222
Parallel Operation
To increase the drive current to a load, both of the amplifiers
within the AD815 can be connected in parallel. Each amplifier
should be set for the same gain and driven with the same signal.
In order to ensure that the two amplifiers share current, a small
resistor should be placed in series with each output. See Figure
48. This circuit can deliver 800 mA into loads of up to 12.5
.
6
4
5
8
+15V
499
V
499
V
1
V
10
7
–15V
499
V
499
V
1
V
R
L
9
11
50
V
0.1
m
F
10
m
F
0.1
m
F
10
m
F
1/2
AD815
1/2
AD815
100
V
100
V
Figure 48. Parallel Operation for High Current Output
Differential Operation
Various circuit configurations can be used for differential
operation of the AD815. If a differential drive signal is avail-
able, the two halves can be used in a classic instrumentation
configuration to provide a circuit with differential input and
output. The circuit in Figure 49 is an illustration of this. With
the resistors shown, the gain of the circuit is 11. The gain can
be changed by changing the value of R
G
. This circuit, however,
provides no common-mode rejection.
6
4
5
8
+15V
10
7
–15V
R
F
499
V
R
L
9
11
0.1
m
F
10
m
F
R
G
100
V
R
F
499
V
0.1
m
F
10
m
F
1/2
AD815
V
OUT
V
IN
1/2
AD815
100
V
100
V
+IN
–IN
OUT 1
OUT 2
Figure 49. Fully-Differential Operation
Creating Differential Signals
If only a single ended signal is available to drive the AD815 and
a differential output signal is desired, several circuits can be
used to perform the single-ended-to-differential conversion.
One circuit to perform this is to use a dual op amp as a
predriver that is configured as a noninverter and inverter. The
circuit shown in Figure 50 performs this function. It uses an
AD826 dual op amp with the gain of one amplifier set at +1 and
the gain of the other at –1. The 1 k
resistor across the input
terminals of the follower makes the noise gain (NG = 1) equal
to the inverter’s. The two outputs then differentially drive the
inputs to the AD815 with no common-mode signal to first order.
相關PDF資料 |
PDF描述 |
|---|---|
| AD815AVR | High Output Current Differential Driver |
| AD815AY | High Output Current Differential Driver |
| AD815AYS | High Output Current Differential Driver |
| AD815 | High Output Current Differential Driver(高輸出電流差分驅動器) |
| AD816 | 500 mA Differential Driver & Dual Low Noise (VF) Amplifiers(500mA差分驅動器和雙低噪電壓反饋放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD816 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SILICON DUAL DIFFERNTIAL AMPLIFIER TRANSISTORS |
| AD816AVR | 制造商:Rochester Electronics LLC 功能描述:ADSL TRANSCEIVER - Bulk |
| AD816AY | 制造商:Rochester Electronics LLC 功能描述:ADSL TRANSCEIVER - Bulk |
| AD816AYR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。