- 您現在的位置：買賣IC網 > PDF目錄373939 > AD8175 (Analog Devices, Inc.) Video Crosspoint Switch PDF資料下載
參數資料
| 型號： | AD8175 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Video Crosspoint Switch |
| 中文描述： | 視頻交叉點開關 |
| 文件頁數： | 37/40頁 |
| 文件大小： | 533K |
| 代理商： | AD8175 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁
AD8175
Rev. 0 | Page 37 of 40
AD8175
OPn
ONn
IPn
INn
50
0
Figure 53. Fly-By Input Termination (Grounds for the two transmission lines
shown must be tied together close to the INn pin)
If multiple AD8175s are to be driven in parallel, a fly-by input
termination scheme is very useful, but the distance from each
AD8175 input to the driven input transmission line is a stub
that should be minimized in length and parasitics using the
discussed guidelines.
When driving the AD8175 single-endedly, the undriven input is
often terminated with a resistance in order to balance the input
stage. It can be seen that by terminating the undriven input with
a resistor of one-half the characteristic impedance, the input
stage will be perfectly balanced (25 Ω, for example, to balance
the two parallel 50 Ω terminations on the driven input).
However, due to the feedback in the input receiver, there is high
speed signal current leaving the undriven input. In order to
terminate this high speed signal, proper transmission line
techniques should be used. One solution is to adjust the trace
width to create a transmission line of half the characteristic
impedance and terminate the far end with this resistance (25 Ω
in a 50 Ω system). This is not often practical as trace widths
become large. In most cases, the best practical solution is to
place the half-characteristic impedance resistor as close as
possible (preferably less than 1.5 cm away) and to reduce the
parasitics of the stub (by removing the ground plane under the
stub, for example). In either case, the designer must decide if
the layout complexity created by a balanced, terminated
solution is preferable to simply grounding the undriven input at
the ball with no trace.
While the examples discussed so far are for input termination,
the theory is similar for output back-termination. Taking the
AD8175 as an ideal voltage source, any distance of routing
between the AD8175 and a back-termination resistor will be an
impedance mismatch that potentially creates reflections. For
this reason, back-termination resistors should also be placed
close to the AD8175. In practice, because back-termination
resistors are series elements, they can be placed close to the
AD8175 outputs.
Finally, the AD8175 pinout allows the user to bring the outputs
out as surface traces to the back-termination resistors. The
designer can avoid creating stubs and reflections by keeping the
AD8175 output signal path on the surface of the board. A stub
is created when a top-to-bottom via connection is made on the
output signal path that is perpendicular to the signal flow.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8175ABPZ | Video Crosspoint Switch |
| AD8175-EVALZ | Video Crosspoint Switch |
| AD8176-EVAL | 475 MHz, Triple 16 】 9 Video Crosspoint Switch |
| AD8176 | 475 MHz, Triple 16 】 9 Video Crosspoint Switch |
| AD8176ABPZ | 475 MHz, Triple 16 】 9 Video Crosspoint Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8175ABPZ | 功能描述:IC CROSSPOINT SWITCH TRPL 676BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| AD8175-EVALZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Video Crosspoint Switch |
| AD8176 | 制造商:AD 制造商全稱:Analog Devices 功能描述:475 MHz, Triple 16 】 9 Video Crosspoint Switch |
| AD8176ABPZ | 功能描述:IC VIDEO CROSSPOINT SWIT 676BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，FCBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| AD8176-EVAL | 制造商:AD 制造商全稱:Analog Devices 功能描述:475 MHz, Triple 16 】 9 Video Crosspoint Switch |
發布緊急采購，3分鐘左右您將得到回復。