- 您現在的位置：買賣IC網 > PDF目錄373941 > AD8210YRZ (ANALOG DEVICES INC) High Voltage, Bidirectional Current Shunt Monitor PDF資料下載
參數資料
| 型號： | AD8210YRZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | High Voltage, Bidirectional Current Shunt Monitor |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | ROHS COMPLIANT, MS-012AA, SOIC-8 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 287K |
| 代理商： | AD8210YRZ |
AD8210
MODES OF OPERATION
The AD8210 can be adjusted for unidirectional or bidirectional
operation.
Rev. 0 | Page 11 of 16
UNIDIRECTIONAL OPERATION
Unidirectional operation allows the AD8210 to measure
currents through a resistive shunt in one direction. The basic
modes for unidirectional operation are ground referenced
output mode and V+ referenced output mode.
In unidirectional operation, the output can be set at the negative
rail (near ground) or at the positive rail (near V+) when the
differential input is 0 V. The output moves to the opposite rail
when a correct polarity differential input voltage is applied. In
this case, full scale is approximately 250 mV. The required
polarity of the differential input depends on the output voltage
setting. If the output is set at ground, then the polarity needs to
be positive to move the output up (see Table 5). If the output is
set at the positive rail, then the input polarity needs to be
negative to move the output down (see Table 6).
Ground Referenced Output
When using the AD8210 in this mode, both reference inputs
are tied to ground, which causes the output to sit at the negative
rail when the differential input voltage is zero (see Figure 27
and Table 4).
AD8210
OUTPUT
G = +20
R
S
+IN
–IN
V
S
V
REF
1
V
REF
2
GND
0
0.1μF
Figure 27. Ground Referenced Output
Table 4. V+ = 5 V
V
IN
(Referred to IN)
0 V
250 mV
V
O
0.05 V
4.9 V
V+ Referenced Output
This mode is set when both reference pins are tied to the
positive supply. It is typically used when the diagnostic scheme
requires detection of the amplifier and wiring before power is
applied to the load (see Figure 28 and Table 5).
AD8210
OUTPUT
G = +20
R
S
+IN
–IN
V
S
V
REF
1
V
REF
2
GND
0.1μF
0
Figure 28. V+ Referenced Output
Table 5. V+ = 5 V
V
IN
(Referred to IN)
0 V
250 mV
BIDIRECTIONAL OPERATION
Bidirectional operation allows the AD8210 to measure currents
through a resistive shunt in two directions. The output offset
can be set anywhere within the output range. Typically, it is set
at half scale for equal measurement range in both directions. In
some cases, however, it is set at a voltage other than half scale
when the bidirectional current is nonsymmetrical.
V
O
4.9 V
0.05 V
Table 6. V+ = 5 V, V
O
= 2.5 V with V
IN
= 0 V
V
IN
(Referred to –IN)
+125 mV
125 mV
Adjusting the output can also be accomplished by applying
voltage(s) to the reference inputs.
V
O
4.9 V
0.05 V
相關PDF資料 |
PDF描述 |
|---|---|
| AD8210YRZ-REEL | High Voltage, Bidirectional Current Shunt Monitor |
| AD8210YRZ-REEL7 | High Voltage, Bidirectional Current Shunt Monitor |
| AD8211 | High Voltage Current Shunt Monitor |
| AD8211YRJZ-R21 | High Voltage Current Shunt Monitor |
| AD8211YRJZ-RL1 | High Voltage Current Shunt Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8210YRZ-REEL | 功能描述:IC CURRENT MONITOR 0.5% 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩流/電流管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 功能:電流開關 檢測方法:- 精確度:±10% 輸入電壓:1.7 V ~ 5.5 V 電流 - 輸出:600mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
| AD8210YRZ-REEL7 | 功能描述:IC CURRENT MONITOR 0.5% 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩流/電流管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 功能:電流開關 檢測方法:- 精確度:±10% 輸入電壓:1.7 V ~ 5.5 V 電流 - 輸出:600mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
| AD8211 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Voltage Current Shunt Monitor |
| AD8211WYRJZ-R7 | 制造商:Analog Devices 功能描述:CURRENT SHUNT MONITOR 5PIN SOT-23 - Tape and Reel |
| AD8211WYRJZ-RL | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。