- 您現在的位置：買賣IC網 > PDF目錄373942 > AD8309ARU-REEL (ANALOG DEVICES INC) 5 MHz.500 MHz 100 dB Demodulating Logarithmic Amplifier with Limiter Output PDF資料下載
參數資料
| 型號： | AD8309ARU-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 5 MHz.500 MHz 100 dB Demodulating Logarithmic Amplifier with Limiter Output |
| 中文描述： | LOG OR ANTILOG AMPLIFIER, 495 MHz BAND WIDTH, PDSO16 |
| 封裝： | TSSOP-16 |
| 文件頁數： | 19/20頁 |
| 文件大小： | 311K |
| 代理商： | AD8309ARU-REEL |
REV. B
AD8309
–19–
Table IV. Evaluation Board Setup Options
Component
Function
Default Condition
SW1
Device Enable. When in position A, the ENBL pin is connected to +V
S
and the
AD8309 is in normal operating mode. In position B, the ENBL pin is connected
to an SMA connector labeled Ext Enable. An applied signal can be applied to this
connector to enable/disable the AD8309. If left open, the ENBL pin will float to
ground putting the device in power-down mode.
SW1 = A
R1
This pad is used to ac-couple to ground for single-ended input drive. To drive the
AD8309 differentially, R1 should be removed.
Input Interface. The 52.3
resistor in position R/L along with C1 and C2 create
a high pass input filter whose corner frequency (640 kHz) is equal to 1/(
π
RC),
where C = C1 = C2 and R is the parallel combination of 52.3
and the AD8309’s
input impedance of 1000
. Alternatively, the 52.3
resistor can be replaced by
an inductor to form an input matching network. See Input Matching Network
section for more details.
R1 = 0
R/L, C1, C2
R/L= 52.3
C1 = C2 = 0.01
μ
F
R3/R4
Slope Adjust. A simple slope adjustment can be implemented by adding a resistive
divider at the VLOG output. R3 and R4, whose sum should be about 1 k
, and
never less than 40
(see specs), set the slope according to the equation:
Slope
= 20
mV
/
dB
×
R
4/(
R
3+
R
4).
R3 = 0
R4 =
`
L1, C5, C6
Limiter Output Coupling. C5 and C6 ac-couple the limiter’s differential outputs.
By adjusting these values and installing an inductor in L1, an output matching
network can be implemented.
L1 = Open
C5 = 0.01
μ
F
C6 = 0.01
μ
F
LK1 Installed. R8 = 402
R8, LK1
Limiter Output Current. With LK2 installed, R8 enables and sets the limiter
output current. The limiter’s output current is set according to the equation
(
I
OUT
= 400
mV
/R
8
). The limiter current can be as high as 10 mA (R8 = 40
).
To disable the limiter (recommended if the limiter is not being used), LK3 should
be removed.
C7
RSSI Bandwidth Adjust. The addition of C7 will lower the RSSI bandwidth of the
VLOG output according to the equation:
f
CORNER
= 12.7
×
10
–
6/(
C
FILT
+ 3.5
pF
).
C7 = Open
Figure 41. Layout of Signal Layer
Figure 42. Layout of Power Layer
相關PDF資料 |
PDF描述 |
|---|---|
| AD8309-EVAL | 5 MHz.500 MHz 100 dB Demodulating Logarithmic Amplifier with Limiter Output |
| AD8309ARU | 5 MHz.500 MHz 100 dB Demodulating Logarithmic Amplifier with Limiter Output |
| AD8309ARU-REEL7 | 5 MHz.500 MHz 100 dB Demodulating Logarithmic Amplifier with Limiter Output |
| AD830 | High Speed, Video Difference Amplifier(高速,視頻差分運放) |
| AD8313ARM-REEL7 | 0.1 GHz-2.5 GHz, 70 dB Logarithmic Detector/Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8309ARU-REEL7 | 功能描述:IC LOG AMP DEMODULATING 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8309ARUZ | 功能描述:IC LOGARITHM AMP 100DB 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8309ARUZ | 制造商:Analog Devices 功能描述:IC LOGARITHMIC AMP 67NS TSSOP-16 |
| AD8309ARUZ-REEL7 | 功能描述:IC AMP LOG DEMODULATING 16TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| AD8309-EVAL | 制造商:Analog Devices 功能描述:AD8309 EVALUATION BOARD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。