- 您現在的位置：買賣IC網 > PDF目錄373946 > AD841SH (ANALOG DEVICES INC) Wideband, Unity-Gain Stable, Fast Settling Op Amp PDF資料下載
參數資料
| 型號： | AD841SH |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Wideband, Unity-Gain Stable, Fast Settling Op Amp |
| 中文描述： | OP-AMP, 5500 uV OFFSET-MAX, 40 MHz BAND WIDTH, MBCY12 |
| 封裝： | METAL CAN, TO-8, 12 PIN |
| 文件頁數： | 8/8頁 |
| 文件大小： | 354K |
| 代理商： | AD841SH |
AD841
REV. B
–8–
C
P
Figure 25. Circuit for Driving a Large Capacitive Load
USING A HEAT SINK
The AD841 draws less quiescent power than most precision
high speed amplifiers and is specified for operation without a
heat sink. However, when driving low impedance loads, the cur-
rent to the load can be 4 to 5 times the quiescent current. This
will create a noticeable temperature rise. Improved performance
can be achieved by using a small heat sink such as the Aavid
Engineering #602B.
TERMINATED LINE DRIVER
The AD841 functions very well as a high speed line driver of ei-
ther terminated or unterminated cables. Figure 26 shows the
AD841 driving a doubly terminated cable in a follower configu-
ration. The AD841 maintains a typical slew rate of 300 V/
μ
s,
which means it can drive a
±
10 V, 4.7 MHz signal or a
±
3 V,
15.9 MHz signal.
The termination resistor, R
T
, (when equal to the characteristic
impedance of the cable) minimizes reflections from the far end
of the cable. A back-termination resistor (R
BT
, also equal to the
characteristic impedance of the cable) may be placed between
the AD841 output and the cable in order to damp any stray sig-
nals caused by a mismatch between R
T
and the cable’s charac-
teristic impedance. This will result in a “cleaner” signal, but
since 1/2 the output voltage will be dropped across R
BT
, the op
amp must supply double the output signal required if there is no
back termination. Therefore the full power bandwidth is cut in
half.
If termination is not used, cables appear as capacitive loads. If
this capacitive load is large, it should be decoupled from the
AD841 by a resistor in series with the output (see above:
Driving a Capacitive Load).
Figure 26. Line Driver Configuration
OVERDRIVE RECOVERY
Figure 27 shows the overdrive recovery capability of the AD841.
Typical recovery time is 200 ns from negative overdrive and
700 ns from positive overdrive.
Figure 27. Overdrive Recovery
Figure 28. Overdrive Recovery Test Circuit
E-20A
20-Terminal Leadless
Ceramic Chip Carrier
12-Lead Metal Can Package
(TO-8 Style)
14-Pin Cerdip (Q) Package
14-Pin Plastic (N) Package
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
相關PDF資料 |
PDF描述 |
|---|---|
| AD841SQ | Wideband, Unity-Gain Stable, Fast Settling Op Amp |
| AD841JQ | Wideband, Unity-Gain Stable, Fast Settling Op Amp |
| AD841KQ | Wideband, Unity-Gain Stable, Fast Settling Op Amp |
| AD847A | High Speed, Low Power Monolithic Op Amp |
| AD847J | High Speed, Low Power Monolithic Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD841SH/883B | 制造商:Analog Devices 功能描述:OP Amp Single GP 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD841SHZ | 制造商:Analog Devices 功能描述:OP Amp Single GP 制造商:Analog Devices 功能描述:OP Amp Single GP ±18V 12-Pin TO-8 |
| AD841SQ | 功能描述:IC OPAMP GP 40MHZ 50MA 14CDIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| AD841SQ/883B | 功能描述:高速運算放大器 FAST SETTLING H.S. OP AMP RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 產品: |
| AD842 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Wideband, High Output Current, Fast Settling Op Amp |
發布緊急采購，3分鐘左右您將得到回復。