- 您現在的位置：買賣IC網 > PDF目錄373947 > AD8532 (Analog Devices, Inc.) Low Cost, 250 mA Output Single-Supply Amplifiers(低成本,250mA輸出,單電源雙放大器) PDF資料下載
參數資料
| 型號： | AD8532 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Cost, 250 mA Output Single-Supply Amplifiers(低成本,250mA輸出,單電源雙放大器) |
| 中文描述： | 低成本，250 mA輸出單電源放大器（低成本，250mA的輸出，單電源雙放大器） |
| 文件頁數： | 12/16頁 |
| 文件大小： | 220K |
| 代理商： | AD8532 |
AD8531/AD8532/AD8534
REV. A
–12–
A Single-Supply Headphone Amplifier
Because of its speed and large output drive, the AD8531/AD8532/
AD8534 makes an excellent headphone driver, as illustrated in
Figure 40. Its low supply operation and rail-to-rail inputs and
outputs give a maximum signal swing on a single +5 V supply.
T o ensure maximum signal swing available to drive the head-
phone, the amplifier inputs are biased to V+/2, which in this
case is 2.5 V. T he 100 k
resistor to the positive supply is
equally split into two 50 k
resistors, with their common point
bypassed by 10
μ
F to prevent power supply noise from contami-
nating the audio signal.
T he audio signal is then ac-coupled to each input through a
10
μ
F capacitor. A large value is needed to ensure that the
20 Hz audio information is not blocked. If the input already has
the proper dc bias, the ac coupling and biasing resistors are not
required. A 270
μ
F capacitor is used at the output to couple the
amplifier to the headphone. T his value is much larger than that
used for the input because of the low impedance of the head-
phones, which can range from 32
to 600
. An additional
16
resistor is used in series with the output capacitor to pro-
tect the op amp’s output stage by limiting capacitor discharge
current. When driving a 48
load, the circuit exhibits less than
0.3% T HD+N at output drive levels of 4 V p-p.
1/2
AD8532
16
50k
270μF
LEFT
HEADPHONE
10μF
50k
50k
100k
10μF
LEFT
INPUT
+V + 5V
1/2
AD8532
16
50k
270μF
RIGHT
HEADPHONE
10μF
50k
50k
100k
10μF
RIGHT
INPUT
+V
+V + 5V
1μF/0.1μF
Figure 40. A Single-Supply, Stereo Headphone Driver
A Single-Supply, T wo-Way Loudspeaker Crossover Network
Active filters are useful in loudspeaker crossover networks for
reasons of small size, relative freedom from parasitic effects, the
ease of controlling low/high channel drive and the controlled driver
damping provided by a dedicated amplifier. Both Sallen-K ey
(SK ) and multiple-feedback (MFB) filter architectures are use-
ful in implementing active crossover networks. T he circuit
shown in Figure 41 is a single-supply, two-way active crossover
which combines the advantages of both filter topologies. T his
active crossover exhibits less than 0.4% T HD+N at output lev-
els of 1.4 V rms using general purpose unity-gain HP/L P stages.
In this two-way example, the L O signal is a dc-500 Hz L P
woofer output, and the HI signal is the HP (>500 Hz)
tweeter output. U1B forms an L P section at 500 Hz, while
U1A provides a HP section, covering frequencies
≥
500 Hz.
V
IN
3
2
1
U1A
AD8532
+V
S
4
R1
31.6k
C1
0.01μF
C2
0.01μF
R2
31.6k
R5
31.6k
R6
31.6k
R4
49.9
HI
LO
500Hz
AND UP
DC –
500Hz
6
5
7
C3
0.01μF
U1B
AD8532
C4
0.02μF
R7
15.8k
R3
49.9
+
+
100k
+V
S
10μF
100k
100k
C
IN
10μF
R
IN
100k
0.1μF
100μF/25V
+V
S
TO U1
+5V
COM
100k
Figure 41. A Single-Supply, Two-Way Active Crossover
T he crossover example frequency of 500 Hz can be shifted
lower or higher by frequency scaling of either resistors or ca-
pacitors. In configuring the circuit for other frequencies,
complementary L P/HP action must be maintained between
sections, and component values within the sections must be in
the same ratio. T able II provides a design aid to adaptation,
with suggested standard component values for other frequencies.
T able II. RC Component Selection for Various
Crossover Frequencies
Crossover
Frequency (Hz)
100
200
319
500
1 k
2 k
5 k
10 k
R1/C1 (U1A)
1
R5/C3 (U1B)
2
160 k
/0.01
μ
F
80.6 k
/0.01
μ
F
49.9 k
/0.01
μ
F
31.6 k
/0.01
μ
F
16 k
/0.01
μ
F
8.06 k
/0.01
μ
F
3.16 k
/0.01
μ
F
1.6 k
/0.01
μ
F
NOT ES
Applicable for filter
α
= 2.
1
For Sallen-K ey stage U1A: R1 = R2, and C1 = C2, etc.
2
For Multiple Feedback stage U1B: R6 = R5, R7 = R5/2, and
C4 = 2C3.
For additional information on the active filters and active cross-
over networks, please consult the data sheet for the OP279, a
dual rail-to-rail high-output current operational amplifier.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8534 | Low Cost, 250 mA Output Single-Supply Amplifiers(低成本,250mA輸出,單電源四放大器) |
| AD8538_07 | Low Power, Precision, Auto-Zero Op Amps |
| AD8539 | Low Power, Precision, Auto-Zero Op Amps |
| AD8541AKS-R2 | General Purpose CMOS Rail-to-Rail Amplifiers |
| AD8541AKS-REEL7 | General Purpose CMOS Rail-to-Rail Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8532AN | 制造商:Analog Devices 功能描述:OP AMP DUAL HIGH O/P RRI/O 8532 |
| AD8532AR | 功能描述:IC OPAMP GP R-R CMOS 3MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 |
| AD8532ARM | 制造商:Analog Devices 功能描述: |
| AD8532ARM-R2 | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O 6V 8-Pin MSOP T/R |
| AD8532ARM-REEL | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O 6V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:CMOS RAIL/RAIL INPUT/OUTPUT OP AMP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。