- 您現在的位置：買賣IC網 > PDF目錄373953 > AD8628ART-R2 (ANALOG DEVICES INC) Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifier PDF資料下載
參數資料
| 型號： | AD8628ART-R2 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifier |
| 中文描述： | OP-AMP, 10 uV OFFSET-MAX, 2 MHz BAND WIDTH, PDSO5 |
| 封裝： | MO-178AA, SOT-23, 5 PIN |
| 文件頁數： | 16/20頁 |
| 文件大小： | 476K |
| 代理商： | AD8628ART-R2 |
AD8628/AD8629
INPUT OVERVOLTAGE PROTECTION
Although the AD8628/AD8629 are rail-to-rail input amplifiers,
care should be taken to ensure that the potential difference
between the inputs does not exceed the supply voltage. Under
normal negative feedback operating conditions, the amplifier
corrects its output to ensure that the two inputs are at the same
voltage. However, if either input exceeds either supply rail by
more than 0.3 V, large currents begin to flow through the ESD
protection diodes in the amplifier.
Rev. C | Page 16 of 20
These diodes are connected between the inputs and each supply
rail to protect the input transistors against an electrostatic
discharge event and are normally reverse-biased. However, if the
input voltage exceeds the supply voltage, these ESD diodes can
become forward-biased. Without current limiting, excessive
amounts of current could flow through these diodes, causing
permanent damage to the device. If inputs are subject to
overvoltage, appropriate series resistors should be inserted to
limit the diode current to less than 5 mA maximum.
OUTPUT PHASE REVERSAL
Output phase reversal occurs in some amplifiers when the input
common-mode voltage range is exceeded. As common-mode
voltage is moved outside of the common-mode range, the
outputs of these amplifiers can suddenly jump in the opposite
direction to the supply rail. This is the result of the differential
input pair shutting down, causing a radical shifting of internal
voltages that results in the erratic output behavior.
The AD8628/AD8629 amplifiers have been carefully designed
to prevent any output phase reversal, provided that both inputs
are maintained within the supply voltages. If one or both inputs
could exceed either supply voltage, a resistor should be placed in
series with the input to limit the current to less than 5 mA. This
ensures that the output does not reverse its phase.
OVERLOAD RECOVERY TIME
Many auto-zero amplifiers are plagued by a long overload
recovery time, often in ms, due to the complicated settling
behavior of the internal nulling loops after saturation of the
outputs. The AD8628/AD8629 have been designed so that
internal settling occurs within two clock cycles after output
saturation happens. This results in a much shorter recovery
time, less than 10 μs, when compared to other auto-zero
amplifiers. The wide bandwidth of the AD8628/AD8629
enhances performance when they are used to drive loads that
inject transients into the outputs. This is a common situation
when an amplifier is used to drive the input of switched
capacitor ADCs.
TIME (500
μ
s/DIV)
V
V
OUT
0V
0V
V
IN
0
CH1 = 50mV/DIV
CH2 = 1V/DIV
A
V
= –50
Figure 56. Positive Input Overload Recovery for the AD8628
TIME (500
μ
s/DIV)
V
V
OUT
0V
0V
V
IN
0
CH1 = 50mV/DIV
CH2 = 1V/DIV
A
V
= –50
Figure 57. Positive Input Overload Recovery for LTC2050
TIME (500
μ
s/DIV)
V
V
OUT
0V
0V
V
IN
0
CH1 = 50mV/DIV
CH2 = 1V/DIV
A
V
= –50
Figure 58. Positive Input Overload Recovery for LMC2001
相關PDF資料 |
PDF描述 |
|---|---|
| AD8628ART-REEL7 | Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifier |
| AD8628ARZ | Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifier |
| AD8629 | Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifier |
| AD8628 | Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Low Noise Operational Amplifier |
| AD8629ARZ1 | Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8628ART-REEL7 | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Single R-R I/O 制造商:Analog Devices 功能描述:IC OP-AMP SINGLE R/R |
| AD8628ARTZ | 制造商:Analog Devices 功能描述:OP AMP ZERO DRIFT R/R SOT23-5 制造商:Analog Devices 功能描述:OP AMP, ZERO DRIFT, R/R, SOT23-5 |
| AD8628ARTZ-R2 | 功能描述:IC OPAMP CHOPPER R-R SOT23-5 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| AD8628ARTZ-R2 | 制造商:Analog Devices 功能描述:IC, OP-AMP, 2.5MHZ, 1V/ us, SOT-23-5 |
| AD8628ARTZ-REEL7 | 功能描述:IC OPAMP CHOPPER R-R SOT23-5 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
發布緊急采購，3分鐘左右您將得到回復。