- 您現在的位置：買賣IC網 > PDF目錄373956 > AD871SD (ANALOG DEVICES INC) Complete 12-Bit 5 MSPS Monolithic A/D Converter PDF資料下載
參數資料
| 型號： | AD871SD |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Complete 12-Bit 5 MSPS Monolithic A/D Converter |
| 中文描述： | 1-CH 12-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP28 |
| 封裝： | SIDE BRAZED, CERAMIC, DIP-28 |
| 文件頁數： | 6/16頁 |
| 文件大小： | 378K |
| 代理商： | AD871SD |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
AD871
REV. A
–6–
OVERVOLTAGE RECOVERY TIME
Overvoltage recovery time is defined as that amount of time
required for the ADC to achieve a specified accuracy after an
overvoltage (50% greater than full-scale range), measured from
the time the overvoltage signal reenters the converter’s range.
DYNAMIC SPECIFICATIONS
SIGNAL-TO-NOISE AND DISTORTION (S/N+D) RATIO
S/N+D is the ratio of the rms value of the measured input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/N+D is expressed in decibels.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first six harmonic com-
ponents to the rms value of the measured input signal and is
expressed as a percentage or in decibels.
INTERMODULATION DISTORTION (IMD)
With inputs consisting of sine waves at two frequencies, fa and
fb, any device with nonlinearities will create distortion products,
of order (m + n), at sum and difference frequencies of mfa
±
nfb, where m, n = 0, 1, 2, 3 . . . . Intermodulation terms are
those for which m or n is not equal to zero. For example, the
second order terms are (fa + fb) and (fa – fb), and the third or-
der terms are (2 fa + fb), (2 fa – fb), (fa + 2 fb) and (2 fb – fa).
The IMD products are expressed as the decibel ratio of the rms
sum of the measured input signals to the rms sum of the distor-
tion terms. The two signals are of equal amplitude and the peak
value of their sums is –0.5 dB from full scale. The IMD prod-
ucts are normalized to a 0 dB input signal.
FULL-POWER BANDWIDTH
The full-power bandwidth is that input frequency at which the
amplitude of the reconstructed fundamental is reduced by 3 dB
for a full-scale input.
SPURIOUS FREE DYNAMIC RANGE
The difference, in dB, between the rms amplitude of the input
signal and the peak spurious signal.
ORDERING GUIDE
Model
Temperature Range
Package Option
1
AD871JD
AD871JE
AD871SD
2
AD871SE
2
0
°
C to +70
°
C
0
°
C to +70
°
C
–55
°
C to +125
°
C
–55
°
C to +125
°
C
D-28
E-44A
D-28
E-44A
NOTES
1
D = Side Brazed Ceramic DIP, E = Leadless Ceramic Chip Carrier.
2
MIL-STD-883 version will be available; contact factory.
DEFINITIONS OF SPECIFICATIONS
LINEARITY ERROR
Linearity error refers to the deviation of each individual code
from a line drawn from “negative full scale” through “positive
full scale.” The point used as “negative full scale” occurs
1/2 LSB before the first code transition. “Positive full scale” is
defined as a level 1 1/2 LSB beyond the last code transition.
The deviation is measured from the middle of each particular
code to the true straight line.
DIFFERENTIAL LINEARITY ERROR (DNL, NO MISSING
CODES)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 12-bit resolution indicates that all 4096
codes must be present over all operating ranges.
ZERO ERROR
The major carry transition should occur for an analog value 1/2
LSB below analog common. Zero error is defined as the devia-
tion of the actual transition from that point. The zero error and
temperature drift specify the initial deviation and maximum
change in the zero error over temperature.
GAIN ERROR
The first code transition should occur for an analog value 1/2
LSB above nominal negative full scale. The last transition
should occur for an analog value 1 1/2 LSB below the nominal
positive full scale. Gain error is the deviation of the actual dif-
ference between first and last code transitions and the ideal dif-
ference between first and last code transitions.
TEMPERATURE DRIFT
The temperature drift for zero error and gain error specifies the
maximum change from the initial (25
°
C) value to the value at
T
MIN
or T
MAX
.
POWER SUPPLY REJECTION
The specifications show the maximum change in the converter’s
full-scale as the supplies are varied from nominal to min/max
values.
APERTURE JITTER
Aperture jitter is the variation in aperture delay for successive
samples and is manifested as noise on the input to the A/D.
APERTURE DELAY
Aperture delay is a measure of the Track-and-Hold Amplifier
(THA) performance and is measured from the rising edge of the
clock input to when the input signal is held for conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| AD871SE | Complete 12-Bit 5 MSPS Monolithic A/D Converter |
| AD871 | Complete 12-Bit 5 MSPS Monolithic A/D Converter(12位5MSPS單片A/D轉換器) |
| AD872A | Complete 12-Bit 10 MSPS Monolithic A/D Converter |
| AD872AJD | Complete 12-Bit 10 MSPS Monolithic A/D Converter |
| AD872AJE | Complete 12-Bit 10 MSPS Monolithic A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD871SD/883B | 制造商:Rochester Electronics LLC 功能描述:IC, 12-BIT 5MSPS ADC IC - Bulk 制造商:Analog Devices 功能描述: |
| AD871SD883B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCIRCUIT, LINEAR, A/D CONVERTER, 12-BIT, 5 MSPS, MONOLITHIC SILICON |
| AD871SE | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 12-Bit 5 MSPS Monolithic A/D Converter |
| AD871SE/883B | 制造商:Rochester Electronics LLC 功能描述:IC, 12-BIT 5MSPS ADC IC - Bulk 制造商:Analog Devices 功能描述: |
| AD871SE883B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCIRCUIT, LINEAR, A/D CONVERTER, 12-BIT, 5 MSPS, MONOLITHIC SILICON |
發布緊急采購，3分鐘左右您將得到回復。