- 您現在的位置：買賣IC網 > PDF目錄373959 > AD9211-250EB (Analog Devices, Inc.) 10-Bit, 170/200/250 MSPS 1.8 V A/D Converter PDF資料下載
參數資料
| 型號： | AD9211-250EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 10-Bit, 170/200/250 MSPS 1.8 V A/D Converter |
| 中文描述： | 10位，170/200/250 MSPS的1.8弗吉尼亞州/ D轉換器 |
| 文件頁數： | 17/21頁 |
| 文件大?。?/td> | 310K |
| 代理商： | AD9211-250EB |
Preliminary Technical Data
AD9211
Rev. PrA | Page 17 of 21
Figure 14. AD9211-250, Supply Current vs. f
SAMPLE
for f
IN
= 10.3 MHz
By asserting the PDWN pin high, the AD9211 is placed in
standby mode. In this state, the ADC typically dissipates
1 mW even if the CLK and analog inputs are static. During
standby, the output drivers are placed in a high impedance state.
Reasserting the PDWN pin low returns the AD9211 into its
normal operational mode.
An additional stand by mode is supported by means of varying
the clock input. When the clock rate falls below 20MHz, the
AD9211 will assume a standby state. In this case, the biasing
network and internal reference remain on but digital circuitry is
powered down. Upon reactivating the clock, the AD9211 will
resume normal operation after allowing for the pipeline latency.
DIGITAL OUTPUTS
The AD9228’s differential outputs conform to the ANSI-644
LVDS standard on default power up. The LVDS driver current
is derived on-chip and sets the output current at each output
equal to a nominal 3.5 mA. A 100 Ω differential termination
resistor placed at the LVDS receiver inputs results in a nominal
350 mV swing at the receiver.
The AD9211’s LVDS outputs facilitate interfacing with LVDS
receivers in custom ASICs and FPGAs that have LVDS capa-
bility for superior switching performance in noisy environ-
ments. Single point-to-point net topologies are recommended
with a 100 Ω termination resistor placed as close to the receiver
as possible. It is recommended to keep the trace length no
longer than 12 inches and to keep differential output traces
close together and at equal lengths.
The format of the output data is offset binary. An example of
the output coding format can be found in Table 7.
Table 7. Digital Output Coding
(VIN+) (VIN),
Input Span =
1.252 V p-p (V)
(D9 ... D0)
1024
1.000
11 1111 1111
512
0
10 0000 0000
511
0.000488
01 1111 1111
0
1.00
00 0000 0000
Code
Digital Output
Offset Binary
As detailed in
Interfacing to ADC SPI
, the data format can be
selected for either offset binary or twos complement, or Gray
code (SPI access only).
Out-of-Range (OTR)
An out-of-range condition exists when the analog input voltage
is beyond the input range of the ADC. OTR is a digital output
that is updated along with the data output corresponding to the
particular sampled input voltage. Thus, OTR has the same
pipeline latency as the digital data. OTR is low when the analog
input voltage is within the analog input range and high when
the analog input voltage exceeds the input range as shown in
Figure 15. OTR will remain high until the analog input returns
to within the input range and another conversion is completed.
By logically AND-ing OTR with the MSB and its complement,
over-range high or under-range low conditions can be detected.
Figure 15. OTR Relation to Input Voltage and Output Data for
AD9230/AD9211
TIMING
The AD9211 provides latched data outputs with a pipeline delay
of five clock cycles. Data outputs are available one propagation
delay (t
PD
) after the rising edge of the clock signal.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9211BCPZ-170 | 10-Bit, 170/200/250 MSPS 1.8 V A/D Converter |
| AD9211BCPZ-200 | 10-Bit, 170/200/250 MSPS 1.8 V A/D Converter |
| AD9211BCPZ-250 | 10-Bit, 170/200/250 MSPS 1.8 V A/D Converter |
| AD9212 | Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter |
| AD9212-65EBZ | Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9211-250EBZ | 功能描述:數據轉換 IC 開發工具 10-Bit 250 Msps ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| AD9211-300EBZ | 功能描述:數據轉換 IC 開發工具 10-Bit 300 Msps ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| AD9211BCPZ-170 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 170/200/250 MSPS 1.8 V A/D Converter |
| AD9211BCPZ-200 | 功能描述:IC ADC 10-BIT 200MSPS 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9211BCPZ-250 | 功能描述:IC ADC 10-BIT 250MSPS 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。