- 您現在的位置：買賣IC網 > PDF目錄373959 > AD9212BCPZ-65 (ANALOG DEVICES INC) Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter PDF資料下載
參數資料
| 型號： | AD9212BCPZ-65 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter |
| 中文描述： | 8-CH 10-BIT FLASH METHOD ADC, SERIAL ACCESS, QCC64 |
| 封裝： | 9 X 9 MM, ROHS COMPLIANT, MO-220VMMD-4, LFCSP-64 |
| 文件頁數： | 19/56頁 |
| 文件大小： | 1840K |
| 代理商： | AD9212BCPZ-65 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
AD9212
THEORY OF OPERATION
The AD9212 architecture consists of a pipelined ADC that is
divided into three sections: a 4-bit first stage followed by eight
1.5-bit stages and a final 3-bit flash. Each stage provides
sufficient overlap to correct for flash errors in the preceding
stages. The quantized outputs from each stage are combined
into a final 10- result in the digital correction logic. The
pipelined architecture permits the first stage to operate on a
new input sample while the remaining stages operate on preceding
samples. Sampling occurs on the rising edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
The output staging block aligns the data, carries out the error
correction, and passes the data to the output buffers. The data is
then serialized and aligned to the frame and output clock.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9212 is a differential switched-capacitor
circuit designed for processing differential input signals. The input
can support a wide common-mode range and maintain excellent
performance. An input common-mode voltage of midsupply
minimizes signal-dependent errors and provides optimum
performance.
Rev. 0 | Page 19 of 56
S
S
H
C
PAR
C
SAMPLE
C
SAMPLE
C
PAR
VIN–
H
S
S
H
VIN+
H
0
Figure 42. Switched-Capacitor Input Circuit
The clock signal alternately switches the input circuit between
sample mode and hold mode (see Figure 42). When the input
circuit is switched into sample mode, the signal source must be
capable of charging the sample capacitors and settling within
one-half of a clock cycle. A small resistor in series with each
input can help reduce the peak transient current injected from
the output stage of the driving source. In addition, low-Q inductors
or ferrite beads can be placed on each leg of the input to reduce
the high differential capacitance seen at the analog inputs, thus
realizing the maximum bandwidth of the ADC. Such use of
low-Q inductors or ferrite beads is required when driving the
converter front end at high IF frequencies. Either a shunt capacitor
or two single-ended capacitors can be placed on the inputs to
provide a matching passive network. This ultimately creates a
low-pass filter at the input to limit any unwanted broadband
noise. See the AN-742 Application Note, the AN-827 Application
Note, and the
Analog Dialogue
article “Transformer-Coupled
Front-End for Wideband A/D Converters” for more information
on this subject. In general, the precise values depend on the
application.
The analog inputs of the AD9212 are not internally dc-biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device so that
V
CM
=
AVDD
/2 is recom-
mended for optimum performance, but the device can function
over a wider range with reasonable performance, as shown in
Figure 45 and Figure 46.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9212BCPZRL7-40 | Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter |
| AD9212BCPZRL7-65 | Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter |
| AD9214 | 10-Bit, 65/80/105 MSPS 3 V A/D Converter |
| AD9214-105PCB | 10-Bit, 65/80/105 MSPS 3 V A/D Converter |
| AD9214-65PCB | 10-Bit, 65/80/105 MSPS 3 V A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9212BCPZRL7-40 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter |
| AD9212BCPZRL7-65 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Octal, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter |
| AD9214 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 65/80/105 MSPS 3 V A/D Converter |
| AD9214-105PCB | 制造商:Analog Devices 功能描述:10 BIT 105MSPS A/D CONV. EVAL BOARD - Bulk |
| AD9214-65PCB | 制造商:Analog Devices 功能描述:10 BIT 65 MSPS A/D CONVERTER EVAL BOARD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。