- 您現在的位置：買賣IC網 > PDF目錄373960 > AD9215BRU-80EB (Analog Devices, Inc.) Circular Connector; No. of Contacts:18; Series:D38999; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:15-18 PDF資料下載
參數資料
| 型號： | AD9215BRU-80EB |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:18; Series:D38999; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:15-18 |
| 中文描述： | 10位，65/80/105 MSPS的，3V的A / D轉換 |
| 文件頁數： | 17/36頁 |
| 文件大小： | 1416K |
| 代理商： | AD9215BRU-80EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD9215
In standby mode, low power dissipation is achieved by shutting
down the reference, reference buffer, and biasing networks. The
decoupling capacitors on REFT and REFB are discharged when
entering standby mode and then must be recharged when
returning to normal operation. As a result, the wake-up time is
related to the time spent in standby mode, and shorter standby
cycles result in proportionally shorter wake-up times. With the
recommended 0.1 μF and 10 μF decoupling capacitors on REFT
and REFB, it takes approximately one second to fully discharge
the reference buffer decoupling capacitors and 7 ms to restore
full operation.
Digital Outputs
The AD9215 output drivers can be configured to interface with
2.5 V or 3.3 V logic families by matching DRVDD to the digital
supply of the interfaced logic. The output drivers are sized to
provide sufficient output current to drive a wide variety of logic
families. However, large drive currents tend to cause current
glitches on the supplies that may affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fanouts may require external buffers or latches.
Timing
The AD9215 provides latched data outputs with a pipeline delay
of five clock cycles. Data outputs are available one propagation
delay (t
OD
) after the rising edge of the clock signal. Refer to
Figure 2 for a detailed timing diagram.
Rev. A | Page 17 of 36
The length of the output data lines and loads placed on them
should be minimized to reduce transients within the AD9215;
these transients can detract from the converter’s dynamic per-
formance.
The lowest typical conversion rate of the AD9215 is 5 MSPS. At
clock rates below 5 MSPS, dynamic performance may degrade.
Voltage Reference
A stable and accurate 0.5 V voltage reference is built into the
AD9215. The input range can be adjusted by varying the refer-
ence voltage applied to the AD9215, using either the internal
reference or an externally applied reference voltage. The input
span of the ADC tracks reference voltage changes linearly.
Internal Reference Connection
A comparator within the AD9215 detects the potential at the
SENSE pin and configures the reference into four possible
states, which are summarized in Table 1 If SENSE is grounded,
the reference amplifier switch is connected to the internal resis-
tor divider (see Figure 36), setting VREF to 1 V. Connecting the
SENSE pin to the VREF pin switches the amplifier output to the
SENSE pin, configuring the internal op amp circuit as a voltage
follower and providing a 0.5 V reference output. If an external
resistor divider is connected as shown in Figure 37, the switch is
again set to the SENSE pin. This puts the reference amplifier in a
noninverting mode with the VREF output defined as
1
×
=
R1
R2
VREF
5
0
10
μ
F+
0.1
μ
F
VREF
SENSE
0.5V
7k
7k
AD9215
VIN–
VIN+
REFT
0.1
μ
F
0.1
μ
F
10
μ
F
0.1
μ
F
REFB
SELECT
LOGIC
ADC
CORE
Figure 36. Internal Reference Configuration
In all reference configurations, REFT and REFB drive the ADC
conversion core and establish its input span. The input range of
the ADC always equals twice the voltage at the reference pin for
either an internal or an external reference.
0
10
μ
F+
0.1
μ
F
VREF
R2
R1
SENSE
0.5V
AD9215
VIN–
VIN+
REFT
0.1
μ
F
0.1
μ
F
10
μ
F
0.1
μ
F
REFB
SELECT
LOGIC
ADC
CORE
Figure 37. Programmable Reference Configuration
If the internal reference of the AD9215 is used to drive multiple
converters to improve gain matching, the loading of the refer-
ence by the other converters must be considered. Figure 38 de-
picts how the internal reference voltage is affected by loading.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9216BCPZRL7-65 | 10-Bit, 65/80/105 MSPS Dual A/D Converter |
| AD9216 | Static Monitor |
| AD9216-105 | 10-Bit, 65/80/105 MSPS Dual A/D Converter |
| AD9216-105PCB | 10-Bit, 65/80/105 MSPS Dual A/D Converter |
| AD9216-40PCB | 10-Bit, 65/80/105 MSPS Dual A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9215BRURL7-105 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 65/80/105 MSPS, 3V A/D Converter |
| AD9215BRURL7-65 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9215BRURL7-80 | 制造商:Analog Devices 功能描述: |
| AD9215BRUZ-105 | 功能描述:IC ADC 10BIT 105MSPS 3V 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9215BRUZ-105 | 制造商:Analog Devices 功能描述:AD CONVERTOR ((NW)) |
發布緊急采購，3分鐘左右您將得到回復。