- 您現在的位置：買賣IC網 > PDF目錄373964 > AD9631 (Analog Devices, Inc.) Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps PDF資料下載
參數資料
| 型號： | AD9631 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps |
| 中文描述： | 超低失真，寬帶電壓反饋運算放大器 |
| 文件頁數： | 17/20頁 |
| 文件大小： | 528K |
| 代理商： | AD9631 |
AD9631/AD9632
REV. A
–17–
R
F
R
O
IN
+V
S
–V
S
R
S
R
T
R
G
OUT
C1
1000pF
C3
0.1
μ
F
C5
10
μ
F
C2
1000pF
C4
0.1
μ
F
C6
10
μ
F
+V
S
–V
S
OPTIONAL
R
F
R
O
IN
+V
S
–V
S
R
T
R
G
OUT
R
S
Inverting Configuration
Noninverting Configuration
Supply Bypassing
Figure 65. Inverting and Noninverting Configurations for
Evaluation Boards
Table I.
AD9631A
Gain
+2
AD9632A
Gain
+10
Component
–1
+1
+10
+100
–1
+2
+100
R
F
R
G
R
O
(Nominal)
R
S
R
T
(Nominal)
Small Signal
BW (MHz)
274
274
49.9
100
61.9
140
274
274
49.9
100
49.9
2 k
221
49.9
100
49.9
2 k
20.5
49.9
100
49.9
274
274
100
100
61.9
274
274
100
100
49.9
2 k
221
49.9
100
49.9
2 k
20.5
49.9
100
49.9
49.9
130
49.9
90
320
90
10
1.3
250
250
20
3
Layout Considerations
The specified high speed performance of the AD9631 and
AD9632 requires careful attention to board layout and compo-
nent selection. Proper RF design techniques and low pass para-
sitic component selection are mandatory.
The PCB should have a ground plane covering all unused por-
tions of the component side of the board to provide a low im-
pedance path. The ground plane should be removed from the
area near the input pins to reduce stray capacitance.
Chip capacitors should be used for the supply bypassing (see
Figure 64). One end should be connected to the ground plane
and the other within 1/8 inch of each power pin. An additional
large (0.47
μ
F–10
μ
F) tantalum electrolytic capacitor should be
connected in parallel, though not necessarily so close, to supply
current for fast, large signal changes at the output.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the in-
verting input will significantly affect high speed performance.
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). These should be designed with a
characteristic impedance of 50
or 75
and be properly termi-
nated at each end.
Evaluation Board
An evaluation board for both the AD9631 and AD9632 is avail-
able that has been carefully laid out and tested to demonstrate
that the specified high speed performance of the device can be
realized. For ordering information, please refer to the Ordering
Guide.
The layout of the evaluation board can be used as shown or
serve as a guide for a board layout.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9631-EB | Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps |
| AD9660KR-REEL | 200 MHz Laser Diode Driver with Light Power Control |
| AD9660 | 200 MHz Laser Diode Driver with Light Power Control |
| AD9660KR | 200 MHz Laser Diode Driver with Light Power Control |
| AD9661A | Laser Diode Driver with Light Power Control(帶光功率控制的激光二極管驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9631_03 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps |
| AD9631AN | 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk 制造商:Rochester Electronics LLC 功能描述:WIDE BW, GAIN=1 OP AMP - Bulk 制造商:Analog Devices 功能描述:OP AMP LOW DISTORTION 9631 DIP8 |
| AD9631ANZ | 功能描述:IC OPAMP VF ULDIST 70MA 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD9631AR | 功能描述:IC OPAMP VF ULDIST 70MA 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| AD9631AR-EBZ | 功能描述:BOARD EVAL FOR AD9631AR RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。