- 您現在的位置：買賣IC網 > PDF目錄373971 > AD9937KCP (ANALOG DEVICES INC) CCD Signal Processor with Precision Timing⑩ Generator PDF資料下載
參數資料
| 型號： | AD9937KCP |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | CCD Signal Processor with Precision Timing⑩ Generator |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, QCC56 |
| 封裝： | MO-220-VLLD-2, LFCSP-56 |
| 文件頁數： | 18/44頁 |
| 文件大小： | 410K |
| 代理商： | AD9937KCP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
REV. 0
–18–
AD9937
SERIAL INTERFACE TIMING
All of the internal registers of the AD9937 are accessed through
a 3-wire serial interface. The 3-wire interface consists of a clock
(SCK), serial load (SLD), and serial data (SDA).
The AD9937 has three different register types that are configured
by the 3-wire serial interface pins. As described in Table VII,
the three register types are control registers, system registers,
and mode registers.
Table VII. Serial Interface Registers
Register
Address
No. of Registers
Control Registers
0x00 to
0x12
24-Bit Register at Each
Address. See Table I.
VTP Sequence
System Registers
0x14
Fourteen 32-Bit System
Registers at Address
0x14. See Table II.
H/LM System
Registers
0x15
Ten 32-Bit System
Registers at Address
0x15. See Table III.
Shutter System
Registers
0x16
Five 32-Bit System
Registers at Address
0x16. See Table IV.
Mode_A
0x17
Twenty 32-Bit Mode_A
Registers at Address
0x17. See Table V.
Mode_B
0x18
Twenty 32-Bit Mode_B
Registers at Address
0x18. See Table VI.
Control Register Serial Interface
The control register 3-wire interface timing requirements are
shown in Figure 5. Writing to control registers requires eight bits of
address data followed by 24 bits of configuration data between
each active low period of SLD for each address. The SLD signal
must be kept high for at least one full SCK cycle between suc-
cessive writes to control registers.
System and Mode Register Serial Interface
The AD9937 provides two options for writing to system and
mode registers. The Page/Burst write option is used when all the
registers are going to be written to, whereas the Random Access
option is used when only one or a small contiguous sequence of
registers is going to be written to. As shown in Figure 6, the
protocol for writing to system and mode registers requires eight
bits for the address data, 12 bits for the start location, 12 bits
for the end location, and 32 bits for the register data.
Page/Burst Option
The AD9937 is automatically configured for Page/Burst mode if
both 12-bit STARTADDRESS and ENDADDRESS fields
equal 0. In this configuration, the AD9937 expects all registers
to be written to, therefore all register data must be clocked in
before the SLD pulse is asserted high. The SLD pulse is ignored
until all register data is clocked in. The Page/Burst option is
preferred when initially programming the system and mode
registers at startup.
Random Access Option
With the Random Access option, the 12-bit STARTADDRESS
and ENDADDRESS fields are typically used when writing to
one system or mode register or a small sequential number of
system or mode registers. In this mode, the address data selects
the system or mode register bank that is going to be accessed,
the 12-bit STARTADDRESS determines the first register to be
accessed, and the 12-bit ENDADDRESS determines the last
register to be accessed. Two examples of Random Access are
provided below (refer to Figure 6).
Example 1: Accessing Only One Register, HLM_Reg(6)
HLM_Reg_addr[A7:A0] = 0x15
STARTADDRESS[S11:S0] = 0x0006
ENDADDRESS[E11:E0] = 0x0006
Example 2: Accessing HLM_Reg(2), HLM_Reg(3), and
HLM_Reg(4) Sequentially
HLM_Reg_addr[A7:A0] = 0x15
STARTADDRESS[S11:S0] = 0x0002
ENDADDRESS[E11:E0] = 0x0004
SDA
SCK
SLD
A5
A6
D22
D21
D3
D2
D1
1. SDA BITS ARE INTERNALLY LATCHED ON THE RISING EDGES OF SCK.
2. THIS TIMING PATTERN MUST BE WRITTEN FOR EACH REGISTER WRITE WITH SLD REMAINING HIGH FOR AT
LEAST ONE FULL SCK PERIOD BEFORE ASSERTING SLD LOW AGAIN FOR THE NEXT REGISTER WRITE.
A7
A4
A3
A2
A1
A0
D23
....
....
D0
1
2
3
4
5
6
7
8
9
10
11
29
30
31
t
LH
32
t
DS
t
DH
t
LS
Figure 5. 3-Wire Serial Interface Timing for Control Registers
相關PDF資料 |
PDF描述 |
|---|---|
| AD9937KCPRL | TVPS00RF-25-35PB W/ PC CONTACT |
| AD9942 | Dual-Channel, 14-Bit CCD Signal Processor with Precision Timing⑩ Core |
| AD9942BBCZ | Dual-Channel, 14-Bit CCD Signal Processor with Precision Timing⑩ Core |
| AD9942BBCZRL | Dual-Channel, 14-Bit CCD Signal Processor with Precision Timing⑩ Core |
| AD9943 | Label Printer Tape RoHS Compliant: NA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9937KCPRL | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3V 56-Pin LFCSP EP T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD9938BCBZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9938BCPZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9938KCP | 制造商:Analog Devices 功能描述:- Bulk |
| AD9940BCPZ | 功能描述:IC CDS TIMING DRIVE CONV 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。