- 您現在的位置：買賣IC網 > PDF目錄373971 > AD9945 (Analog Devices, Inc.) Complete 12-Bit 40 MHz CCD Signal Processor PDF資料下載
參數資料
| 型號： | AD9945 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Complete 12-Bit 40 MHz CCD Signal Processor |
| 中文描述： | 完整的12位40 MHz的CCD信號處理器 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 217K |
| 代理商： | AD9945 |
REV. A
AD9945
–13–
Internal Power-On Reset Circuitry
After power-on, the AD9945 will automatically reset all internal
registers and perform internal calibration procedures. This takes
approximately 1 ms to complete. During this time, normal clock
signals and serial write operations may occur. However, serial
register writes will be ignored until the internal reset operation
is completed.
Grounding and Decoupling Recommendations
As shown in Figure 11, a single ground plane is recommended for
the AD9945. This ground plane should be as continuous as
possible. This will ensure that all analog decoupling capacitors
provide the lowest possible impedance path between the power
and bypass pins and their respective ground pins. All decoupling
capacitors should be located as close as possible to the package
pins. A single clean power supply is recommended for the AD9945,
but a separate digital driver supply may be used for DRVDD
(Pin 11). DRVDD should always be decoupled to DRVSS (Pin 12),
which should be connected to the analog ground plane. Advan-
tages of using a separate digital driver supply include using a
lower voltage (2.7 V) to match levels with a 2.7 V ASIC, reducing
digital power dissipation, and reducing potential noise coupling.
If the digital outputs (Pins 1 to 10, 31, and 32) must drive a
load larger than 20 pF, buffering is recommended to reduce
digital code transition noise. Alternatively, placing series resis-
tors close to the digital output pins may also help reduce noise.
24 REFB
23 REFT
22 CCDIN
21 AVSS
20 AVDD
D2 1
D3 2
D4 3
3
19 SHD
18 SHP
17 CLPOB
D5 4
D6 5
D7 6
D8 7
D9 8
3
3
2
2
2
2
2
DATA
OUTPUTS
12
D
D
9
1
3V
DRIVER
SUPPLY
D
D
D
D
D
P
1
1
1
1
1
3V
ANALOG
SUPPLY
5
CLOCK
INPUTS
3
SERIAL
INTERFACE
3V
ANALOG
SUPPLY
CCDIN
PIN 1
IDENTIFIER
AD9945
(Not to Scale)
TOP VIEW
1.0 F
0.1 F
0.1 F
0.1 F
0.1 F
D0
D1
NC = NO CONNECT
1
1.0 F
NOTE
THE EXPOSED PAD ON THE BOTTOM OF THE AD9945 SHOULD BE
SOLDERED TO THE GND PLANE OF THE PRINTED CIRCUIT BOARD
Figure 11. Recommended Circuit Configuration for CCD Mode
相關PDF資料 |
PDF描述 |
|---|---|
| AD9945KCP | Complete 12-Bit 40 MHz CCD Signal Processor |
| AD9945KCPRL | Complete 12-Bit 40 MHz CCD Signal Processor |
| AD9945KCPRL7 | Complete 12-Bit 40 MHz CCD Signal Processor |
| AD9945KCPZ2 | Complete 12-Bit 40 MHz CCD Signal Processor |
| AD9945KCPZRL72 | Complete 12-Bit 40 MHz CCD Signal Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9945KCP | 制造商:Analog Devices 功能描述:AFE Video 1ADC 12-Bit 3V 32-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:12 BIT 40 MSPS FRONT END CONVERTER - Bulk |
| AD9945KCPRL | 制造商:Analog Devices 功能描述:AFE Video 1ADC 12-Bit 3V 32-Pin LFCSP EP T/R 制造商:Rochester Electronics LLC 功能描述:12 BIT 40 MSPS FRONT END CONVERTER - Tape and Reel |
| AD9945KCPRL7 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD9945KCPZ | 功能描述:IC CCD SIGNAL PROCESSOR 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9945KCPZ | 制造商:Analog Devices 功能描述:CCD Signal Processor IC |
發布緊急采購，3分鐘左右您將得到回復。