- 您現在的位置：買賣IC網 > PDF目錄373973 > ADA4431-1YCPZ-R7 (ANALOG DEVICES INC) Ultralow Power SD Video Filter with Load Detection PDF資料下載
參數資料
| 型號： | ADA4431-1YCPZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | Ultralow Power SD Video Filter with Load Detection |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, QCC16 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, MO-248UEED, LFCSP-16 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 389K |
| 代理商： | ADA4431-1YCPZ-R7 |
ADA4431-1
THEORY OF OPERATION
OVERVIEW
The ADA4431-1 is designed for exceptional performance as
both a filter and a low power driver for portable video applications.
This performance is achieved by providing third-order filtering
without trading off power consumption or device size. While
consuming only 4.7 mA quiescent supply current, the ADA4431-1
provides video output on a single-supply as low as 2.5 V
The ADA4431-1 also features a load detect circuit, which senses
current through the external 75 Ω back-termination resistor.
When either no video load or a short circuit is detected, the
ADA4431-1 enters a low power state. In this state, it draws
0.1 mA, continues to monitor the load current, and powers up
automatically when a video load is connected. Optionally, the
ADA4431-1 can be powered down via the disable pin (DIS).
Another external pin (LDO) outputs the load detection state
(for example, to an external system controller). This pin is high
(+V
S
) when a video load is present, and low (0 V) in the absence
of a video load or when the output is short-circuited.
The ADA4431-1 is intended for use in applications that have
both ac- and dc-coupled inputs and outputs. The rail-to-rail
buffer on the ADA4431-1 output is able to drive 2 V p-p video
signals into two doubly terminated video loads (150 Ω each) on
a single 2.5 V supply. The ADA4431-1 has a gain of 2 when the
SAG correction pin is tied directly to the output, which makes
up for the 6 dB termination loss (see Figure 17, Output Option 1).
When the SAG feature is used, the ADA4431-1 has a low
frequency gain of 2.5 (
≈
8 dB) and a high frequency gain of 2
(see Figure 17, Output Option 2). Signal offsets and supply levels
must be considered when using the SAG correction feature to
ensure that there are no headroom issues.
The input range of the ADA4431-1 includes ground, while the
output range is limited by the saturation of the output devices.
Saturation occurs several tens of mV from the positive and
negative supply rails.
Rev. 0 | Page 9 of 12
The high input impedance and low input capacitance of the
ADA4431-1 offer advantages in a number of low power
applications. In reconstruction filter applications, the DAC can
be placed in its lowest power mode, allowing the use of a large-
valued load resistor. Using a large-valued load resistor does not
interfere with the frequency response of the ADA4431-1.
CHARGE PUMP OPERATION
The on-board charge pump creates a virtual negative supply for
the output driver, which allows the output signal to be dc-coupled,
with its black level at 0 V and sync tip at 300 mV. The charge
pump is enabled whenever the disable pin (DIS) is held high.
If DIS is left floating, or placed in a high impedance state, the
ADA4431-1 is powered up, but the charge pump is disabled,
which is typically the case for ac-coupling of the output. When
DIS is driven to 0 V, the entire device is powered down.
Table 6. Disable (DIS) Pin Function Summary
DIS Pin
Device State
Low
Disabled
High
Enabled
High-Z
Enabled
Charge Pump State
Disabled
Enabled
Disabled
LOAD DETECT
The load detect feature provides additional system power
management to keep the power consumption of a portable
device to the absolute minimum. The ADA4431-1 monitors the
output load for three conditions: a normal load, a shorted load,
and an open load. Each of these conditions occurs for a video
load, an audio load, and no load, respectively. Only in the video
load condition will the ADA4431-1 power up from 0.1 mA to
4.7 mA. A single I/O pin, LDO, notifies the system by either
being high for a video load or low for a short and open load.
With this information, it is intended that the system controller
power down any power intensive video processing blocks to
realize substantial power savings. The ADA4431-1 operates
autonomously, requiring no inputs to monitor the condition of
the output load.
相關PDF資料 |
PDF描述 |
|---|---|
| ADA4431-1YCPZ-RL | Ultralow Power SD Video Filter with Load Detection |
| ADA4841-1 | Low Power, Low Noise and Distortion, Rail-to-Rail Output Amplifier |
| ADA4841-1YRJZ-R2 | Low Power, Low Noise and Distortion, Rail-to-Rail Output Amplifier |
| ADA4841-1YRJZ-R7 | Low Power, Low Noise and Distortion, Rail-to-Rail Output Amplifier |
| ADA4841-1YRJZ-RL | Low Power, Low Noise and Distortion, Rail-to-Rail Output Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4431-1YCPZ-RL | 功能描述:IC SD VIDEO FILTER ULP 16LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ADA4431-1YCPZ-RZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADA4431-1YCPZ-TR | 制造商:Analog Devices 功能描述:LOW PWR COMP VIDEO FLTR W/ULP DISABLE - Tape and Reel |
| ADA4432-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SD Video Filter Amplifiers |
| ADA4432-1BCP-EBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:SD Video Filter Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。