- 您現在的位置：買賣IC網 > PDF目錄373975 > ADAU1592ACPZ (ANALOG DEVICES INC) Class-D Audio Power Amplifier PDF資料下載
參數資料
| 型號： | ADAU1592ACPZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Class-D Audio Power Amplifier |
| 中文描述： | 24 W, 2 CHANNEL, AUDIO AMPLIFIER, QCC48 |
| 封裝： | 7 X 7 MM, ROHS COMPLIANT, MO-220VKKD-2, LFCSP-48 |
| 文件頁數： | 16/24頁 |
| 文件大小： | 457K |
| 代理商： | ADAU1592ACPZ |
ADAU1592
Rev. 0 | Page 16 of 24
0
V
CM
SLICER_LEVEL
50k
V
TH
PIN 24 (SLC_TH)
R
EXTERNAL
Figure 43. Block for Slicer Threshold Adjust, SLC_TH
The slicer threshold can be set externally using a resistor as
follows:
V
TH
= (
AVDD
/2) × (50 kΩ/50 kΩ +
R
EXTERNAL
)
where:
AVDD
= 3.3 V typical.
V
TH
is the voltage threshold at which the slicer is activated.
The following equation can be used to calculate the input signal
at which the slicer becomes active:
V
V
0.9
1.414
×
=
TH
IN RMS
Therefore, for
AVDD
= 3.3 V typical and
V
TH
= 1.1 V,
R
EXTERNAL
= 24.9 kΩ
V
IN RMS
= 0.864 V
Thus, the slicer is activated at and above 0.864 V
IN RMS
.
This feature allows the user to set the slicer and, in turn, reduces
the output power at a given supply voltage.To disable the slicer,
SLC_TH should be connected to AGND. Table 9 shows the
typical values for R
EXTERNAL
.
Table 9. Typical R
EXTERNAL
Values
V
TH
(V)
1.1
1.17
1.24
1.32
R
EXTERNAL
(kΩ)
24.9
20.5
16.5
12.4
V
IN RMS
(V)
0.864
0.919
0.974
1.037
POWER STAGE
The ADAU1592 power stage comprises a high-side PMOS and
a low-side NMOS. The typical R
DS-ON
is ~ 300 mΩ. The PMOS-
NMOS stage does not need an external bootstrap capacitor and
simplifies the high-side driver design. The power stage also has
comprehensive protection circuits to detect the faults in typical
applications. See the Protection Circuits section for further details.
GAIN
The gain of the amplifier is set internally using feedback
resistors optimized for 15 V nominal operation. The typical
gain values are tabulated in Table 1. The typical gain is 19 dB
with PGA set to 0 dB. PGA0 (Pin 14) and PGA1 (Pin 13) are used
for setting the desired gain.
The gain can be set according to Table 10. Note that the ampli-
fier full-scale input level changes as per the PGA gain setting.
Table 10. Gain Settings
PGA1
(Pin 13)
0
0
1
1
PGA0
(Pin 14)
0
1
0
1
PGA
Gain
(dB)
0
6
12
18
Amplifier
Gain (dB)
19
25
31
37
Full-Scale
Input Level
(V
RMS
)
1
0.5
0.25
0.125
PROTECTION CIRCUITS
The ADAU1592 includes comprehensive protection circuits. It
includes thermal warning, thermal overheat, and overcurrent or
short-circuit protection on the outputs. The ERR and OTW
outputs are open drain and require external pull-up resistors.
The outputs are capable of sinking 10 mA. The open-drain
outputs are useful in multichannel applications where more
than one ADAU1592 is used. The error outputs of multiple
ADAU1592s can be OR’ed to simplify the system design. The
logic outputs of the error flags ease the system design of using
a microcontroller.
THERMAL PROTECTION
Thermal protection in the ADAU1592 is categorized into two
error flags: one as thermal warning and the other as thermal
shutdown. When the device junction temperature reaches near
135°C (±5°C), the ADAU1592 outputs a thermal warning error
flag by pulling OTW (Pin 10) low. This flag can be used by the
microcontroller in the system for indication to the user or can
be used to lower the input level to the amplifier to prevent
thermal shutdown. The device continues operation until
shutdown temperature is reached.
When the device junction temperature exceeds 150°C, the
device outputs an error flag by pulling ERR (Pin 9) low. This
error flag is latched. To restore the operation, MUTE (Pin 15)
needs to be toggled to low and then to high again.
OVERCURRENT PROTECTION
The overcurrent protection in the ADAU1592 is set internally
at a 5 A peak output current. The device protects the output
devices against excessive output current by pulling ERR (Pin 9)
low. This error flag is latched. To restore the normal operation,
MUTE (Pin 15) needs to be toggled to low and then to high
again. The error flag is useful for the microcontroller in the
system to indicate abnormal operation and to initiate the audio
MUTE sequence. The device senses the short-circuit condition
on the outputs after the LC filter. Typical short-circuit condi-
tions include shorting of the output load and shorting to either
PVDD or PGND.
相關PDF資料 |
PDF描述 |
|---|---|
| ADAU1592ACPZ-RL | Class-D Audio Power Amplifier |
| ADAU1592ACPZ-RL7 | Class-D Audio Power Amplifier |
| ADAU1592ASVZ | Class-D Audio Power Amplifier |
| ADAU1592ASVZ-RL | Class-D Audio Power Amplifier |
| ADAU1592ASVZ-RL7 | Class-D Audio Power Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADAU1592ACPZ-RL | 功能描述:IC AMP AUDIO PWR 24W 48LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| ADAU1592ACPZ-RL7 | 功能描述:IC AMP AUDIO PWR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
| ADAU1592ASVZ | 制造商:Analog Devices 功能描述:AMP AUDIO CLASS D SMD TQFPEP-48 |
| ADAU1592ASVZ-RL | 制造商:Analog Devices 功能描述: |
| ADAU1592ASVZ-RL7 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。